Having prepared all the required partitions, it is quite easy to configure journaling. We will need to switch to single user mode, so login as root and type:
# shutdown now
Press Enter to get the default shell. We will need to unmount the partitions that will be journaled, in our example /usr and /var:
# umount /usr /var
Load the module required for journaling:
# gjournal load
Now, use your notes to determine which partition will be used for each journal. In our example, /usr is ad0s1f and its journal will be ad0s1g, while /var is ad0s1d and will be journaled to ad0s1h. The following commands are required:
# gjournal label ad0s1f ad0s1g GEOM_JOURNAL: Journal 2948326772: ad0s1f contains data. GEOM_JOURNAL: Journal 2948326772: ad0s1g contains journal. # gjournal label ad0s1d ad0s1h GEOM_JOURNAL: Journal 3193218002: ad0s1d contains data. GEOM_JOURNAL: Journal 3193218002: ad0s1h contains journal.
Note: If the last sector of either partition is used, gjournal will return an error. You will have to run the command using the
-fflag to force an overwrite, i.e.:# gjournal label -f ad0s1d ad0s1hSince this is a new installation, it is highly unlikely that anything will be actually overwritten.
At this point, two new devices are created, namely ad0s1d.journal and ad0s1f.journal. These represent the /var and /usr partitions we have to mount. Before mounting, we must however set the journal flag on them and clear the Soft Updates flag:
# tunefs -J enable -n disable ad0s1d.journal tunefs: gjournal set tunefs: soft updates cleared # tunefs -J enable -n disable ad0s1f.journal tunefs: gjournal set tunefs: soft updates cleared
Now, mount the new devices manually at their respective places (note that we can now
use the async mount option):
# mount -o async /dev/ad0s1d.journal /var # mount -o async /dev/ad0s1f.journal /usr
Edit /etc/fstab and update the entries for /usr and /var:
/dev/ad0s1f.journal /usr ufs rw,async 2 2 /dev/ad0s1d.journal /var ufs rw,async 2 2
Warning: Make sure the above entries are correct, or you will have trouble starting up normally after you reboot!
Finally, edit /boot/loader.conf and add the following line so the gjournal(8) module is loaded at every boot:
geom_journal_load="YES"
Congratulations! Your system is now set for journaling. You can either type exit to return to multi-user mode, or reboot to test your configuration (recommended). During the boot you will see messages like the following:
ad0: 76293MB XEC XE800JD-00HBC0 08.02D08 at ata0-master SATA150 GEOM_JOURNAL: Journal 2948326772: ad0s1g contains journal. GEOM_JOURNAL: Journal 3193218002: ad0s1h contains journal. GEOM_JOURNAL: Journal 3193218002: ad0s1d contains data. GEOM_JOURNAL: Journal ad0s1d clean. GEOM_JOURNAL: Journal 2948326772: ad0s1f contains data. GEOM_JOURNAL: Journal ad0s1f clean.
After an unclean shutdown, the messages will vary slightly, i.e.:
GEOM_JOURNAL: Journal ad0s1d consistent.
This usually means that gjournal(8) used the information in the journal provider to return the file system to a consistent state.
While the above procedure is necessary for journaling partitions that already contain data, journaling an empty partition is somewhat easier, since both the data and the journal provider can be stored in the same partition. For example, assume a new disk was installed, and a new partition /dev/ad1s1d was created. Creating the journal would be as simple as:
# gjournal label ad1s1d
The journal size will be 1 GB by default. You may adjust it by using the -s option. The value can be given in bytes, or appended by K, M or G to
denote Kilobytes, Megabytes or Gigabytes respectively. Note that gjournal will not allow you to create unsuitably small journal
sizes.
For example, to create a 2 GB journal, you could use the following command:
# gjournal label -s 2G ad1s1d
You can then create a file system on your new partition, and enable journaling using
the -J option:
# newfs -J /dev/ad1s1d.journal
If you do not wish to load geom_journal as a module, you can build its functions right into your kernel. Edit your custom kernel configuration file, and make sure it includes these two lines:
options UFS_GJOURNAL # Note: This is already in GENERIC options GEOM_JOURNAL # You will have to add this one
Rebuild and reinstall your kernel following the relevant instructions in the FreeBSD Handbook.
Do not forget to remove the relevant “load” entry from /boot/loader.conf if you have previously used it.