This section contains notes and hints specific to Apache 2.x installs of PHP on Microsoft Windows systems. We also have instructions and notes for Apache 1.3.x users on a separate page.
Bilginize:
You should read the manual installation steps first!
Bilginize: Apache 2.2 Support
Users of Apache 2.2 should note that the DLL file for Apache 2.2 is named php5apache2_2.dll rather than php5apache2.dll and is available only for PHP 5.2.0 and later. See also » http://snaps.php.net/
You are strongly encouraged to consult the » Apache Documentation to get a basic understanding of the Apache 2.x Server. Also consider reading the » Windows specific notes for Apache 2.x before reading on here.
Apache 2.x is designed to run on the Windows version designated as server platforms, such as Windows NT 4.0, Windows 2000, Windows XP, or Windows 7. While Apache 2.x works tolerably well on Windows 9x, support on these platforms is incomplete, and some things will not work correctly. There is no plan to remedy this situation.
Download the most recent version of » Apache 2.x and a fitting PHP version. Follow the Manual Installation Steps and come back to go on with the integration of PHP and Apache.
There are three ways to set up PHP to work with Apache 2.x on Windows. You can run PHP as a handler, as a CGI, or under FastCGI.
Bilginize: Windows üzerinde, Apache yapılandırma dosyalarına c:\dizin\dosya.uzn gibi dosya yollarını eklerken tüm tersbölü çizgilerini normal bölü çizgilerine çevirmeyi unutmayınız: c:/dizin/dosya.uzn. Dizin yollarını eklerken sona da bir bölü çizgisi eklemeniz gerekebilir.
You need to insert the following lines into your Apache httpd.conf configuration file to load the PHP module for Apache 2.x:
Örnek 1 PHP and Apache 2.x as handler
# LoadModule php5_module "c:/php/php5apache2.dll" AddHandler application/x-httpd-php .php # configure the path to php.ini PHPIniDir "C:/php"
Bilginize: Remember to substitute your actual path to PHP for the C:/php/ in the above examples. Take care to use either php5apache2.dll or php5apache2_2.dll in your LoadModule directive and verify that the referenced file is in fact located at the file path that you point to in this directive.
The above configuration will enable PHP handling of any file that has a .php extension, even if there are other file extensions. For example, a file named example.php.txt will be executed by the PHP handler. To ensure that only files that end in .php are executed, use the following configuration instead:
<FilesMatch \.php$>
SetHandler application/x-httpd-php
</FilesMatch>
You should consult the » Apache CGI documentation for a more complete understanding of running CGI on Apache.
To run PHP as CGI, you'll need to place your php-cgi files in a directory designated as a CGI directory using the ScriptAlias directive.
You will then need to insert a #! line in the PHP files, pointing to the location of your PHP binary:
Örnek 2 PHP and Apache 2.x as CGI
#!C:/php/php.exe <?php phpinfo(); ?>
CGI kipinde çalışan bir sunucu olası saldırılara açık hale gelir. Sunucunuzu böyle saldırılardan nasıl koruyacağınızı öğrenmek için CGI güvenliği bölümünü okuyunuz.
Running PHP under FastCGI has a number of advantages over running it as a CGI. Setting it up this way is fairly straightforward:
Obtain mod_fcgid from » http://httpd.apache.org/mod_fcgid/. Win32 binaries are available for download from that site. Install the module according to the instructions that will come with it.
Configure your web server as shown below, taking care to adjust any paths to reflect your how you have installed things on your particular system:
Örnek 3 Configure Apache to run PHP as FastCGI
LoadModule fcgid_module modules/mod_fcgid.so # Where is your php.ini file? FcgidInitialEnv PHPRC "c:/php" AddHandler fcgid-script .php FcgidWrapper "c:/php/php-cgi.exe" .php