slon

The log_level specifies which Debug levels slon should display when logging its activity.

The eight levels of logging are:

• Error

• Warn

• Config

• Info

• Debug1

• Debug2

• Debug3

• Debug4

Thus, all the non-debugging log levels are always displayed in the logs. If log_level is set to 2 (a routine, and, seemingly preferable choice), then output at debugging levels 1 and 2 will also be displayed.

The sync_interval, measured in milliseconds, indicates how often slon should check to see if a SYNC should be introduced. Default is 10000 ms. The main loop in sync_Thread_main() sleeps for intervals of sync_interval milliseconds between iterations.

Short sync check intervals keep the origin on a "short leash", updating its subscribers more frequently. If you have replicated sequences that are frequently updated without there being tables that are affected, this keeps there from being times when only sequences are updated, and therefore no syncs take place

If the node is not an origin for any replication set, so no updates are coming in, it is somewhat wasteful for this value to be much less the sync_interval_timeout value.

At the end of each sync_interval_timeout timeout period, a SYNC will be generated on the "local" node even if there has been no replicatable data updated that would have pushed out a SYNC.

Default, and maximum, is 60000 ms, so that you can expect each node to "report in" with a SYNC once each minute.

Note that SYNC events are also generated on subscriber nodes. Since they are not actually generating any data to replicate to other nodes, these SYNC events are of not terribly much value.

This controls the maximum SYNC group size, sync_group_maxsize; defaults to 6. Thus, if a particular node is behind by 200 SYNCs, it will try to group them together into groups of a maximum size of sync_group_maxsize. This can be expected to reduce transaction overhead due to having fewer transactions to COMMIT.

The default of 6 is probably suitable for small systems that can devote only very limited bits of memory to slon. If you have plenty of memory, it would be reasonable to increase this, as it will increase the amount of work done in each transaction, and will allow a subscriber that is behind by a lot to catch up more quickly.

Slon processes usually stay pretty small; even with large value for this option, slon would be expected to only grow to a few MB in size.

The big advantage in increasing this parameter comes from cutting down on the number of transaction COMMITs; moving from 1 to 2 will provide considerable benefit, but the benefits will progressively fall off once the transactions being processed get to be reasonably large. There isn't likely to be a material difference in performance between 80 and 90; at that point, whether "bigger is better" will depend on whether the bigger set of SYNCs makes the LOG cursor behave badly due to consuming more memory and requiring more time to sortt.

In Slony-I version 1.0, slon will always attempt to group SYNCs together to this maximum, which won't be ideal if replication has been somewhat destabilized by there being very large updates (e.g. - a single transaction that updates hundreds of thousands of rows) or by SYNCs being disrupted on an origin node with the result that there are a few SYNCs that are very large. You might run into the problem that grouping together some very large SYNCs knocks over a slon process. When it picks up again, it will try to process the same large grouped set of SYNCs, and run into the same problem over and over until an administrator interrupts this and changes the -g value to break this "deadlock."

In Slony-I version 1.0, the slon instead adaptively "ramps up" from doing 1 SYNC at a time towards the maximum group size. As a result, if there are a couple of SYNCs that cause problems, the slon will (with any relevant watchdog assistance) always be able to get to the point where it processes the troublesome SYNCs one by one, hopefully making operator assistance unnecessary.

A "maximum" time planned for grouped SYNCs.

If replication is running behind, slon will gradually increase the numbers of SYNCs grouped together, targetting that (based on the time taken for the last group of SYNCs) they shouldn't take more than the specified desired_sync_time value.

The default value for desired_sync_time is 60000ms, equal to one minute.

That way, you can expect (or at least hope!) that you'll get a COMMIT roughly once per minute.

It isn't totally predictable, as it is entirely possible for someone to request a very large update, all as one transaction, that can "blow up" the length of the resulting SYNC to be nearly arbitrarily long. In such a case, the heuristic will back off for the next group.

The overall effect is to improve Slony-I's ability to cope with variations in traffic. By starting with 1 SYNC, and gradually moving to more, even if there turn out to be variations large enough to cause PostgreSQL backends to crash, Slony-I will back off down to start with one sync at a time, if need be, so that if it is at all possible for replication to progress, it will.

The value vac_frequency indicates how often to VACUUM in cleanup cycles.

Set this to zero to disable slon-initiated vacuuming. If you are using something like pg_autovacuum to initiate vacuums, you may not need for slon to initiate vacuums itself. If you are not, there are some tables Slony-I uses that collect a lot of dead tuples that should be vacuumed frequently, notably pg_listener.

In Slony-I version 1.1, this changes a little; the cleanup thread tracks, from iteration to iteration, the earliest transaction ID still active in the system. If this doesn't change, from one iteration to the next, then an old transaction is still active, and therefore a VACUUM will do no good. The cleanup thread instead merely does an ANALYZE on these tables to update the statistics in pg_statistics.

pid_file contains the filename in which the PID (process ID) of the slon is stored.

This may make it easier to construct scripts to monitor multiple slon processes running on a single host.

File from which to read slon configuration.

This configuration is discussed further in Slon Run-time Configuration. If there are to be a complex set of configuration parameters, or if there are parameters you do not wish to be visible in the process environment variables (such as passwords), it may be convenient to draw many or all parameters from a configuration file. You might either put common parameters for all slon processes in a commonly-used configuration file, allowing the command line to specify little other than the connection info. Alternatively, you might create a configuration file for each node.

archive_dir indicates a directory in which to place a sequence of SYNC archive files for use in log shipping mode.

command_on_logarchive indicates a command to be run each time a SYNC file is successfully generated.

See more details on slon_conf_command_on_log_archive.

quit_sync_provider indicates which provider's worker thread should be watched in order to terminate after a certain event. This must be used in conjunction with the -r option below...

This allows you to have a slon stop replicating after a certain point.

quit_sync_finalsync indicates the event number after which the remote worker thread for the provider above should terminate. This must be used in conjunction with the -q option above...

lag_interval indicates an interval value such as 3 minutes or 4 hours or 2 days that indicates that this node is to lag its providers by the specified interval of time. This causes events to be ignored until they reach the age corresponding to the interval.