Settings.Secure

Setting that specifies whether display color inversion is enabled.

If accessibility is enabled.

Whether to speak passwords while in accessibility mode.

Origins for which browsers should allow geolocation by default. The value is a space-separated list of origins.

Setting to allow mock locations and location provider status to be injected into the LocationManager service for testing purposes during application development. These locations and status values override actual location and status information generated by network, gps, or other location providers.

A 64-bit number (as a hex string) that is randomly generated when the user first sets up the device and should remain constant for the lifetime of the user's device. The value may change if a factory reset is performed on the device.

Note: When a device has multiple users (available on certain devices running Android 4.2 or higher), each user appears as a completely separate device, so the ANDROID_ID value is unique to each user.

Whether background data usage is allowed.

Setting to record the input method used by default, holding the ID of the desired method.

List of the enabled accessibility providers.

List of input methods that are currently enabled. This is a string containing the IDs of all enabled input methods, each ID separated by ':'.

Host name and port for global http proxy. Uses ':' seperator for between host and port.

Setting to record the visibility of input method selector

Whether applications can be installed for this user via the system's ACTION_INSTALL_PACKAGE mechanism.

1 = permit app installation via the system package installer intent

0 = do not allow use of the package installer

The degree of location access enabled by the user.

When used with putInt(ContentResolver, String, int), must be one of LOCATION_MODE_HIGH_ACCURACY, LOCATION_MODE_SENSORS_ONLY, LOCATION_MODE_BATTERY_SAVING, or LOCATION_MODE_OFF. When used with getInt(ContentResolver, String), the caller must gracefully handle additional location modes that might be added in the future.

Note: do not rely on this value being present in settings.db or on ContentObserver notifications for the corresponding Uri. Use MODE_CHANGED_ACTION to receive changes in this value.

Reduced power usage, such as limiting the number of GPS updates per hour. Requests with POWER_HIGH may be downgraded to POWER_MEDIUM.

Best-effort location computation allowed.

Location access disabled.

Network Location Provider disabled, but GPS and other sensors enabled.

Comma-separated list of location providers that activities may access. Do not rely on this value being present in settings.db or on ContentObserver notifications on the corresponding Uri.

Whether autolock is enabled (0 = false, 1 = true)

Whether lock pattern will vibrate as user enters (0 = false, 1 = true)

Whether lock pattern is visible as user enters (0 = false, 1 = true)

The Logging ID (a unique 64-bit value) as a hex string. Used as a pseudonymous identifier for logging.

No longer supported.

No longer supported.

No longer supported.

Setting to record the input method subtype used by default, holding the ID of the desired method.

Settings classname to launch when Settings is clicked from All Applications. Needed because of user testing between the old and new Settings apps.

If enabled, apps should try to skip any introductory hints on first launch. This might apply to users that are already familiar with the environment or temporary users.

Type : int (0 to show hints, 1 to skip showing hints)

If touch exploration is enabled.

Default text-to-speech country.

Default text-to-speech language.

Default text-to-speech engine pitch. 100 = 1x

Default text-to-speech engine speech rate. 100 = 1x

Default text-to-speech engine.

Default text-to-speech locale variant.

Space delimited list of plugin packages that are enabled.

Setting to always use the default text-to-speech settings regardless of the application settings. 1 = override application settings, 0 = use application settings (if specified).

The acceptable packet loss percentage (range 0 - 100) before trying another AP on the same network.

The number of access points required for a network in order for the watchdog to monitor it.

The delay between background checks.

Whether the Wi-Fi watchdog is enabled for background checking even after it thinks the user has connected to a good access point.

The timeout for a background ping

The number of initial pings to perform that *may* be ignored if they fail. Again, if these fail, they will *not* be used in packet loss calculation. For example, one network always seemed to time out for the first couple pings, so this is set to 3 by default.

The maximum number of access points (per network) to attempt to test. If this number is reached, the watchdog will no longer monitor the initial connection state for the network. This is a safeguard for networks containing multiple APs whose DNS does not respond to pings.

The number of pings to test if an access point is a good connection.

The delay between pings.

The timeout per ping.

A comma-separated list of SSIDs for which the Wi-Fi watchdog should be enabled.

The content:// style URL for this table

Convenience function for retrieving a single secure settings value as a floating point number. Note that internally setting values are always stored as strings; this function converts the string to an float for you. The default value will be returned if the setting is not defined or not a valid float.

Convenience function for retrieving a single secure settings value as a float. Note that internally setting values are always stored as strings; this function converts the string to a float for you.

This version does not take a default value. If the setting has not been set, or the string value is not a number, it throws Settings.SettingNotFoundException.

Convenience function for retrieving a single secure settings value as an integer. Note that internally setting values are always stored as strings; this function converts the string to an integer for you.

This version does not take a default value. If the setting has not been set, or the string value is not a number, it throws Settings.SettingNotFoundException.

Convenience function for retrieving a single secure settings value as an integer. Note that internally setting values are always stored as strings; this function converts the string to an integer for you. The default value will be returned if the setting is not defined or not an integer.

Convenience function for retrieving a single secure settings value as a long. Note that internally setting values are always stored as strings; this function converts the string to a long for you. The default value will be returned if the setting is not defined or not a long.

Convenience function for retrieving a single secure settings value as a long. Note that internally setting values are always stored as strings; this function converts the string to a long for you.

This version does not take a default value. If the setting has not been set, or the string value is not a number, it throws Settings.SettingNotFoundException.

Look up a name in the database.

Construct the content URI for a particular name/value pair, useful for monitoring changes with a ContentObserver.

Helper method for determining if a location provider is enabled.

Convenience function for updating a single settings value as a floating point number. This will either create a new entry in the table if the given name does not exist, or modify the value of the existing row with that name. Note that internally setting values are always stored as strings, so this function converts the given value to a string before storing it.

Convenience function for updating a single settings value as an integer. This will either create a new entry in the table if the given name does not exist, or modify the value of the existing row with that name. Note that internally setting values are always stored as strings, so this function converts the given value to a string before storing it.

Convenience function for updating a secure settings value as a long integer. This will either create a new entry in the table if the given name does not exist, or modify the value of the existing row with that name. Note that internally setting values are always stored as strings, so this function converts the given value to a string before storing it.

Store a name/value pair into the database.

Thread-safe method for enabling or disabling a single location provider.