MC68VZ328.h

Go to the documentation of this file.

/* include/asm-m68knommu/MC68VZ328.h: 'VZ328 control registers
 *
 * Copyright (c) 2000-2001  Lineo Inc. <www.lineo.com>
 * Copyright (c) 2000-2001  Lineo Canada Corp. <www.lineo.ca>
 * Copyright (C) 1999       Vladimir Gurevich <[email protected]>
 *              Bare & Hare Software, Inc.
 * Based on include/asm-m68knommu/MC68332.h
 * Copyright (C) 1998  Kenneth Albanowski <[email protected]>,
 *                     The Silver Hammer Group, Ltd.
 *
 * M68VZ328 fixes by Evan Stawnyczy <[email protected]>
 * vz multiport fixes by Michael Leslie <[email protected]>
 */

#ifndef _MC68VZ328_H_
#define _MC68VZ328_H_

#define BYTE_REF(addr) (*((volatile unsigned char*)addr))
#define WORD_REF(addr) (*((volatile unsigned short*)addr))
#define LONG_REF(addr) (*((volatile unsigned long*)addr))

#define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK)
#define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT)

/********** 
 *
 * 0xFFFFF0xx -- System Control
 *
 **********/
 
/*
 * System Control Register (SCR)
 */
#define SCR_ADDR    0xfffff000
#define SCR     BYTE_REF(SCR_ADDR)

#define SCR_WDTH8   0x01    /* 8-Bit Width Select */
#define SCR_DMAP    0x04    /* Double Map */
#define SCR_SO      0x08    /* Supervisor Only */
#define SCR_BETEN   0x10    /* Bus-Error Time-Out Enable */
#define SCR_PRV     0x20    /* Privilege Violation */
#define SCR_WPV     0x40    /* Write Protect Violation */
#define SCR_BETO    0x80    /* Bus-Error TimeOut */

/*
 * Silicon ID Register (Mask Revision Register (MRR) for '328 Compatibility)
 */
#define MRR_ADDR 0xfffff004
#define MRR  LONG_REF(MRR_ADDR)

/********** 
 *
 * 0xFFFFF1xx -- Chip-Select logic
 *
 **********/
 
/*
 * Chip Select Group Base Registers 
 */
#define CSGBA_ADDR  0xfffff100
#define CSGBB_ADDR  0xfffff102

#define CSGBC_ADDR  0xfffff104
#define CSGBD_ADDR  0xfffff106

#define CSGBA       WORD_REF(CSGBA_ADDR)
#define CSGBB       WORD_REF(CSGBB_ADDR)
#define CSGBC       WORD_REF(CSGBC_ADDR)
#define CSGBD       WORD_REF(CSGBD_ADDR)

/*
 * Chip Select Registers 
 */
#define CSA_ADDR    0xfffff110
#define CSB_ADDR    0xfffff112
#define CSC_ADDR    0xfffff114
#define CSD_ADDR    0xfffff116

#define CSA     WORD_REF(CSA_ADDR)
#define CSB     WORD_REF(CSB_ADDR)
#define CSC     WORD_REF(CSC_ADDR)
#define CSD     WORD_REF(CSD_ADDR)

#define CSA_EN      0x0001      /* Chip-Select Enable */
#define CSA_SIZ_MASK    0x000e      /* Chip-Select Size */
#define CSA_SIZ_SHIFT   1
#define CSA_WS_MASK 0x0070      /* Wait State */
#define CSA_WS_SHIFT    4
#define CSA_BSW     0x0080      /* Data Bus Width */
#define CSA_FLASH   0x0100      /* FLASH Memory Support */
#define CSA_RO      0x8000      /* Read-Only */

#define CSB_EN      0x0001      /* Chip-Select Enable */
#define CSB_SIZ_MASK    0x000e      /* Chip-Select Size */
#define CSB_SIZ_SHIFT   1
#define CSB_WS_MASK 0x0070      /* Wait State */
#define CSB_WS_SHIFT    4
#define CSB_BSW     0x0080      /* Data Bus Width */
#define CSB_FLASH   0x0100      /* FLASH Memory Support */
#define CSB_UPSIZ_MASK  0x1800      /* Unprotected memory block size */
#define CSB_UPSIZ_SHIFT 11
#define CSB_ROP     0x2000      /* Readonly if protected */
#define CSB_SOP     0x4000      /* Supervisor only if protected */
#define CSB_RO      0x8000      /* Read-Only */

#define CSC_EN      0x0001      /* Chip-Select Enable */
#define CSC_SIZ_MASK    0x000e      /* Chip-Select Size */
#define CSC_SIZ_SHIFT   1
#define CSC_WS_MASK 0x0070      /* Wait State */
#define CSC_WS_SHIFT    4
#define CSC_BSW     0x0080      /* Data Bus Width */
#define CSC_FLASH   0x0100      /* FLASH Memory Support */
#define CSC_UPSIZ_MASK  0x1800      /* Unprotected memory block size */
#define CSC_UPSIZ_SHIFT 11
#define CSC_ROP     0x2000      /* Readonly if protected */
#define CSC_SOP     0x4000      /* Supervisor only if protected */
#define CSC_RO      0x8000      /* Read-Only */

#define CSD_EN      0x0001      /* Chip-Select Enable */
#define CSD_SIZ_MASK    0x000e      /* Chip-Select Size */
#define CSD_SIZ_SHIFT   1
#define CSD_WS_MASK 0x0070      /* Wait State */
#define CSD_WS_SHIFT    4
#define CSD_BSW     0x0080      /* Data Bus Width */
#define CSD_FLASH   0x0100      /* FLASH Memory Support */
#define CSD_DRAM    0x0200      /* Dram Selection */
#define CSD_COMB    0x0400      /* Combining */
#define CSD_UPSIZ_MASK  0x1800      /* Unprotected memory block size */
#define CSD_UPSIZ_SHIFT 11
#define CSD_ROP     0x2000      /* Readonly if protected */
#define CSD_SOP     0x4000      /* Supervisor only if protected */
#define CSD_RO      0x8000      /* Read-Only */

/*
 * Emulation Chip-Select Register 
 */
#define EMUCS_ADDR  0xfffff118
#define EMUCS       WORD_REF(EMUCS_ADDR)

#define EMUCS_WS_MASK   0x0070
#define EMUCS_WS_SHIFT  4

/********** 
 *
 * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control
 *
 **********/

/*
 * PLL Control Register 
 */
#define PLLCR_ADDR  0xfffff200
#define PLLCR       WORD_REF(PLLCR_ADDR)

#define PLLCR_DISPLL           0x0008   /* Disable PLL */
#define PLLCR_CLKEN        0x0010   /* Clock (CLKO pin) enable */
#define PLLCR_PRESC        0x0020   /* VCO prescaler */
#define PLLCR_SYSCLK_SEL_MASK  0x0700   /* System Clock Selection */
#define PLLCR_SYSCLK_SEL_SHIFT 8
#define PLLCR_LCDCLK_SEL_MASK  0x3800   /* LCD Clock Selection */
#define PLLCR_LCDCLK_SEL_SHIFT 11

/* '328-compatible definitions */
#define PLLCR_PIXCLK_SEL_MASK   PLLCR_LCDCLK_SEL_MASK
#define PLLCR_PIXCLK_SEL_SHIFT  PLLCR_LCDCLK_SEL_SHIFT

/*
 * PLL Frequency Select Register
 */
#define PLLFSR_ADDR 0xfffff202
#define PLLFSR      WORD_REF(PLLFSR_ADDR)

#define PLLFSR_PC_MASK  0x00ff      /* P Count */
#define PLLFSR_PC_SHIFT 0
#define PLLFSR_QC_MASK  0x0f00      /* Q Count */
#define PLLFSR_QC_SHIFT 8
#define PLLFSR_PROT 0x4000      /* Protect P & Q */
#define PLLFSR_CLK32    0x8000      /* Clock 32 (kHz) */

/*
 * Power Control Register
 */
#define PCTRL_ADDR  0xfffff207
#define PCTRL       BYTE_REF(PCTRL_ADDR)

#define PCTRL_WIDTH_MASK    0x1f    /* CPU Clock bursts width */
#define PCTRL_WIDTH_SHIFT   0
#define PCTRL_PCEN      0x80    /* Power Control Enable */

/**********
 *
 * 0xFFFFF3xx -- Interrupt Controller
 *
 **********/

/* 
 * Interrupt Vector Register
 */
#define IVR_ADDR    0xfffff300
#define IVR     BYTE_REF(IVR_ADDR)

#define IVR_VECTOR_MASK 0xF8

/*
 * Interrupt control Register
 */
#define ICR_ADDR    0xfffff302
#define ICR     WORD_REF(ICR_ADDR)

#define ICR_POL5    0x0080  /* Polarity Control for IRQ5 */
#define ICR_ET6     0x0100  /* Edge Trigger Select for IRQ6 */
#define ICR_ET3     0x0200  /* Edge Trigger Select for IRQ3 */
#define ICR_ET2     0x0400  /* Edge Trigger Select for IRQ2 */
#define ICR_ET1     0x0800  /* Edge Trigger Select for IRQ1 */
#define ICR_POL6    0x1000  /* Polarity Control for IRQ6 */
#define ICR_POL3    0x2000  /* Polarity Control for IRQ3 */
#define ICR_POL2    0x4000  /* Polarity Control for IRQ2 */
#define ICR_POL1    0x8000  /* Polarity Control for IRQ1 */

/*
 * Interrupt Mask Register
 */
#define IMR_ADDR    0xfffff304
#define IMR     LONG_REF(IMR_ADDR)

/*
 * Define the names for bit positions first. This is useful for 
 * request_irq
 */
#define SPI2_IRQ_NUM    0   /* SPI 2 interrupt */
#define TMR_IRQ_NUM 1   /* Timer 1 interrupt */
#define UART1_IRQ_NUM   2   /* UART 1 interrupt */  
#define WDT_IRQ_NUM 3   /* Watchdog Timer interrupt */
#define RTC_IRQ_NUM 4   /* RTC interrupt */
#define TMR2_IRQ_NUM    5   /* Timer 2 interrupt */
#define KB_IRQ_NUM  6   /* Keyboard Interrupt */
#define PWM1_IRQ_NUM    7   /* Pulse-Width Modulator 1 int. */
#define INT0_IRQ_NUM    8   /* External INT0 */
#define INT1_IRQ_NUM    9   /* External INT1 */
#define INT2_IRQ_NUM    10  /* External INT2 */
#define INT3_IRQ_NUM    11  /* External INT3 */
#define UART2_IRQ_NUM   12  /* UART 2 interrupt */  
#define PWM2_IRQ_NUM    13  /* Pulse-Width Modulator 1 int. */
#define IRQ1_IRQ_NUM    16  /* IRQ1 */
#define IRQ2_IRQ_NUM    17  /* IRQ2 */
#define IRQ3_IRQ_NUM    18  /* IRQ3 */
#define IRQ6_IRQ_NUM    19  /* IRQ6 */
#define IRQ5_IRQ_NUM    20  /* IRQ5 */
#define SPI1_IRQ_NUM    21  /* SPI 1 interrupt */
#define SAM_IRQ_NUM 22  /* Sampling Timer for RTC */
#define EMIQ_IRQ_NUM    23  /* Emulator Interrupt */

#define SPI_IRQ_NUM SPI2_IRQ_NUM

/* '328-compatible definitions */
#define SPIM_IRQ_NUM    SPI_IRQ_NUM
#define TMR1_IRQ_NUM    TMR_IRQ_NUM
#define UART_IRQ_NUM    UART1_IRQ_NUM

/* 
 * Here go the bitmasks themselves
 */
#define IMR_MSPI    (1 << SPI_IRQ_NUM)  /* Mask SPI interrupt */
#define IMR_MTMR    (1 << TMR_IRQ_NUM)  /* Mask Timer interrupt */
#define IMR_MUART   (1 << UART_IRQ_NUM) /* Mask UART interrupt */   
#define IMR_MWDT    (1 << WDT_IRQ_NUM)  /* Mask Watchdog Timer interrupt */
#define IMR_MRTC    (1 << RTC_IRQ_NUM)  /* Mask RTC interrupt */
#define IMR_MKB     (1 << KB_IRQ_NUM)   /* Mask Keyboard Interrupt */
#define IMR_MPWM    (1 << PWM_IRQ_NUM)  /* Mask Pulse-Width Modulator int. */
#define IMR_MINT0   (1 << INT0_IRQ_NUM) /* Mask External INT0 */
#define IMR_MINT1   (1 << INT1_IRQ_NUM) /* Mask External INT1 */
#define IMR_MINT2   (1 << INT2_IRQ_NUM) /* Mask External INT2 */
#define IMR_MINT3   (1 << INT3_IRQ_NUM) /* Mask External INT3 */
#define IMR_MIRQ1   (1 << IRQ1_IRQ_NUM) /* Mask IRQ1 */
#define IMR_MIRQ2   (1 << IRQ2_IRQ_NUM) /* Mask IRQ2 */
#define IMR_MIRQ3   (1 << IRQ3_IRQ_NUM) /* Mask IRQ3 */
#define IMR_MIRQ6   (1 << IRQ6_IRQ_NUM) /* Mask IRQ6 */
#define IMR_MIRQ5   (1 << IRQ5_IRQ_NUM) /* Mask IRQ5 */
#define IMR_MSAM    (1 << SAM_IRQ_NUM)  /* Mask Sampling Timer for RTC */
#define IMR_MEMIQ   (1 << EMIQ_IRQ_NUM) /* Mask Emulator Interrupt */

/* '328-compatible definitions */
#define IMR_MSPIM   IMR_MSPI
#define IMR_MTMR1   IMR_MTMR

/* 
 * Interrupt Status Register 
 */
#define ISR_ADDR    0xfffff30c
#define ISR     LONG_REF(ISR_ADDR)

#define ISR_SPI     (1 << SPI_IRQ_NUM)  /* SPI interrupt */
#define ISR_TMR     (1 << TMR_IRQ_NUM)  /* Timer interrupt */
#define ISR_UART    (1 << UART_IRQ_NUM) /* UART interrupt */    
#define ISR_WDT     (1 << WDT_IRQ_NUM)  /* Watchdog Timer interrupt */
#define ISR_RTC     (1 << RTC_IRQ_NUM)  /* RTC interrupt */
#define ISR_KB      (1 << KB_IRQ_NUM)   /* Keyboard Interrupt */
#define ISR_PWM     (1 << PWM_IRQ_NUM)  /* Pulse-Width Modulator interrupt */
#define ISR_INT0    (1 << INT0_IRQ_NUM) /* External INT0 */
#define ISR_INT1    (1 << INT1_IRQ_NUM) /* External INT1 */
#define ISR_INT2    (1 << INT2_IRQ_NUM) /* External INT2 */
#define ISR_INT3    (1 << INT3_IRQ_NUM) /* External INT3 */
#define ISR_IRQ1    (1 << IRQ1_IRQ_NUM) /* IRQ1 */
#define ISR_IRQ2    (1 << IRQ2_IRQ_NUM) /* IRQ2 */
#define ISR_IRQ3    (1 << IRQ3_IRQ_NUM) /* IRQ3 */
#define ISR_IRQ6    (1 << IRQ6_IRQ_NUM) /* IRQ6 */
#define ISR_IRQ5    (1 << IRQ5_IRQ_NUM) /* IRQ5 */
#define ISR_SAM     (1 << SAM_IRQ_NUM)  /* Sampling Timer for RTC */
#define ISR_EMIQ    (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */

/* '328-compatible definitions */
#define ISR_SPIM    ISR_SPI
#define ISR_TMR1    ISR_TMR

/* 
 * Interrupt Pending Register 
 */
#define IPR_ADDR    0xfffff30c
#define IPR     LONG_REF(IPR_ADDR)

#define IPR_SPI     (1 << SPI_IRQ_NUM)  /* SPI interrupt */
#define IPR_TMR     (1 << TMR_IRQ_NUM)  /* Timer interrupt */
#define IPR_UART    (1 << UART_IRQ_NUM) /* UART interrupt */    
#define IPR_WDT     (1 << WDT_IRQ_NUM)  /* Watchdog Timer interrupt */
#define IPR_RTC     (1 << RTC_IRQ_NUM)  /* RTC interrupt */
#define IPR_KB      (1 << KB_IRQ_NUM)   /* Keyboard Interrupt */
#define IPR_PWM     (1 << PWM_IRQ_NUM)  /* Pulse-Width Modulator interrupt */
#define IPR_INT0    (1 << INT0_IRQ_NUM) /* External INT0 */
#define IPR_INT1    (1 << INT1_IRQ_NUM) /* External INT1 */
#define IPR_INT2    (1 << INT2_IRQ_NUM) /* External INT2 */
#define IPR_INT3    (1 << INT3_IRQ_NUM) /* External INT3 */
#define IPR_IRQ1    (1 << IRQ1_IRQ_NUM) /* IRQ1 */
#define IPR_IRQ2    (1 << IRQ2_IRQ_NUM) /* IRQ2 */
#define IPR_IRQ3    (1 << IRQ3_IRQ_NUM) /* IRQ3 */
#define IPR_IRQ6    (1 << IRQ6_IRQ_NUM) /* IRQ6 */
#define IPR_IRQ5    (1 << IRQ5_IRQ_NUM) /* IRQ5 */
#define IPR_SAM     (1 << SAM_IRQ_NUM)  /* Sampling Timer for RTC */
#define IPR_EMIQ    (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */

/* '328-compatible definitions */
#define IPR_SPIM    IPR_SPI
#define IPR_TMR1    IPR_TMR

/**********
 *
 * 0xFFFFF4xx -- Parallel Ports
 *
 **********/

/*
 * Port A
 */
#define PADIR_ADDR  0xfffff400      /* Port A direction reg */
#define PADATA_ADDR 0xfffff401      /* Port A data register */
#define PAPUEN_ADDR 0xfffff402      /* Port A Pull-Up enable reg */

#define PADIR       BYTE_REF(PADIR_ADDR)
#define PADATA      BYTE_REF(PADATA_ADDR)
#define PAPUEN      BYTE_REF(PAPUEN_ADDR)

#define PA(x)       (1 << (x))

/* 
 * Port B
 */
#define PBDIR_ADDR  0xfffff408      /* Port B direction reg */
#define PBDATA_ADDR 0xfffff409      /* Port B data register */
#define PBPUEN_ADDR 0xfffff40a      /* Port B Pull-Up enable reg */
#define PBSEL_ADDR  0xfffff40b      /* Port B Select Register */

#define PBDIR       BYTE_REF(PBDIR_ADDR)
#define PBDATA      BYTE_REF(PBDATA_ADDR)
#define PBPUEN      BYTE_REF(PBPUEN_ADDR)
#define PBSEL       BYTE_REF(PBSEL_ADDR)

#define PB(x)       (1 << (x))

#define PB_CSB0     0x01    /* Use CSB0      as PB[0] */
#define PB_CSB1     0x02    /* Use CSB1      as PB[1] */
#define PB_CSC0_RAS0    0x04    /* Use CSC0/RAS0 as PB[2] */    
#define PB_CSC1_RAS1    0x08    /* Use CSC1/RAS1 as PB[3] */    
#define PB_CSD0_CAS0    0x10    /* Use CSD0/CAS0 as PB[4] */    
#define PB_CSD1_CAS1    0x20    /* Use CSD1/CAS1 as PB[5] */
#define PB_TIN_TOUT 0x40    /* Use TIN/TOUT  as PB[6] */
#define PB_PWMO     0x80    /* Use PWMO      as PB[7] */

/* 
 * Port C
 */
#define PCDIR_ADDR  0xfffff410      /* Port C direction reg */
#define PCDATA_ADDR 0xfffff411      /* Port C data register */
#define PCPDEN_ADDR 0xfffff412      /* Port C Pull-Down enb. reg */
#define PCSEL_ADDR  0xfffff413      /* Port C Select Register */

#define PCDIR       BYTE_REF(PCDIR_ADDR)
#define PCDATA      BYTE_REF(PCDATA_ADDR)
#define PCPDEN      BYTE_REF(PCPDEN_ADDR)
#define PCSEL       BYTE_REF(PCSEL_ADDR)

#define PC(x)       (1 << (x))

#define PC_LD0      0x01    /* Use LD0  as PC[0] */
#define PC_LD1      0x02    /* Use LD1  as PC[1] */
#define PC_LD2      0x04    /* Use LD2  as PC[2] */
#define PC_LD3      0x08    /* Use LD3  as PC[3] */
#define PC_LFLM     0x10    /* Use LFLM as PC[4] */
#define PC_LLP      0x20    /* Use LLP  as PC[5] */
#define PC_LCLK     0x40    /* Use LCLK as PC[6] */
#define PC_LACD     0x80    /* Use LACD as PC[7] */

/* 
 * Port D
 */
#define PDDIR_ADDR  0xfffff418      /* Port D direction reg */
#define PDDATA_ADDR 0xfffff419      /* Port D data register */
#define PDPUEN_ADDR 0xfffff41a      /* Port D Pull-Up enable reg */
#define PDSEL_ADDR  0xfffff41b      /* Port D Select Register */
#define PDPOL_ADDR  0xfffff41c      /* Port D Polarity Register */
#define PDIRQEN_ADDR    0xfffff41d      /* Port D IRQ enable register */
#define PDKBEN_ADDR 0xfffff41e      /* Port D Keyboard Enable reg */
#define PDIQEG_ADDR 0xfffff41f      /* Port D IRQ Edge Register */

#define PDDIR       BYTE_REF(PDDIR_ADDR)
#define PDDATA      BYTE_REF(PDDATA_ADDR)
#define PDPUEN      BYTE_REF(PDPUEN_ADDR)
#define PDSEL       BYTE_REF(PDSEL_ADDR)
#define PDPOL       BYTE_REF(PDPOL_ADDR)
#define PDIRQEN     BYTE_REF(PDIRQEN_ADDR)
#define PDKBEN      BYTE_REF(PDKBEN_ADDR)
#define PDIQEG      BYTE_REF(PDIQEG_ADDR)

#define PD(x)       (1 << (x))

#define PD_INT0     0x01    /* Use INT0 as PD[0] */
#define PD_INT1     0x02    /* Use INT1 as PD[1] */
#define PD_INT2     0x04    /* Use INT2 as PD[2] */
#define PD_INT3     0x08    /* Use INT3 as PD[3] */
#define PD_IRQ1     0x10    /* Use IRQ1 as PD[4] */
#define PD_IRQ2     0x20    /* Use IRQ2 as PD[5] */
#define PD_IRQ3     0x40    /* Use IRQ3 as PD[6] */
#define PD_IRQ6     0x80    /* Use IRQ6 as PD[7] */

/* 
 * Port E
 */
#define PEDIR_ADDR  0xfffff420      /* Port E direction reg */
#define PEDATA_ADDR 0xfffff421      /* Port E data register */
#define PEPUEN_ADDR 0xfffff422      /* Port E Pull-Up enable reg */
#define PESEL_ADDR  0xfffff423      /* Port E Select Register */

#define PEDIR       BYTE_REF(PEDIR_ADDR)
#define PEDATA      BYTE_REF(PEDATA_ADDR)
#define PEPUEN      BYTE_REF(PEPUEN_ADDR)
#define PESEL       BYTE_REF(PESEL_ADDR)

#define PE(x)       (1 << (x))

#define PE_SPMTXD   0x01    /* Use SPMTXD as PE[0] */
#define PE_SPMRXD   0x02    /* Use SPMRXD as PE[1] */
#define PE_SPMCLK   0x04    /* Use SPMCLK as PE[2] */
#define PE_DWE      0x08    /* Use DWE    as PE[3] */
#define PE_RXD      0x10    /* Use RXD    as PE[4] */
#define PE_TXD      0x20    /* Use TXD    as PE[5] */
#define PE_RTS      0x40    /* Use RTS    as PE[6] */
#define PE_CTS      0x80    /* Use CTS    as PE[7] */

/* 
 * Port F
 */
#define PFDIR_ADDR  0xfffff428      /* Port F direction reg */
#define PFDATA_ADDR 0xfffff429      /* Port F data register */
#define PFPUEN_ADDR 0xfffff42a      /* Port F Pull-Up enable reg */
#define PFSEL_ADDR  0xfffff42b      /* Port F Select Register */

#define PFDIR       BYTE_REF(PFDIR_ADDR)
#define PFDATA      BYTE_REF(PFDATA_ADDR)
#define PFPUEN      BYTE_REF(PFPUEN_ADDR)
#define PFSEL       BYTE_REF(PFSEL_ADDR)

#define PF(x)       (1 << (x))

#define PF_LCONTRAST    0x01    /* Use LCONTRAST as PF[0] */
#define PF_IRQ5         0x02    /* Use IRQ5      as PF[1] */
#define PF_CLKO         0x04    /* Use CLKO      as PF[2] */
#define PF_A20          0x08    /* Use A20       as PF[3] */
#define PF_A21          0x10    /* Use A21       as PF[4] */
#define PF_A22          0x20    /* Use A22       as PF[5] */
#define PF_A23          0x40    /* Use A23       as PF[6] */
#define PF_CSA1     0x80    /* Use CSA1      as PF[7] */

/* 
 * Port G
 */
#define PGDIR_ADDR  0xfffff430      /* Port G direction reg */
#define PGDATA_ADDR 0xfffff431      /* Port G data register */
#define PGPUEN_ADDR 0xfffff432      /* Port G Pull-Up enable reg */
#define PGSEL_ADDR  0xfffff433      /* Port G Select Register */

#define PGDIR       BYTE_REF(PGDIR_ADDR)
#define PGDATA      BYTE_REF(PGDATA_ADDR)
#define PGPUEN      BYTE_REF(PGPUEN_ADDR)
#define PGSEL       BYTE_REF(PGSEL_ADDR)

#define PG(x)       (1 << (x))

#define PG_BUSW_DTACK   0x01    /* Use BUSW/DTACK as PG[0] */
#define PG_A0       0x02    /* Use A0         as PG[1] */
#define PG_EMUIRQ   0x04    /* Use EMUIRQ     as PG[2] */
#define PG_HIZ_P_D  0x08    /* Use HIZ/P/D    as PG[3] */
#define PG_EMUCS        0x10    /* Use EMUCS      as PG[4] */
#define PG_EMUBRK   0x20    /* Use EMUBRK     as PG[5] */

/* 
 * Port J
 */
#define PJDIR_ADDR  0xfffff438      /* Port J direction reg */
#define PJDATA_ADDR 0xfffff439      /* Port J data register */
#define PJPUEN_ADDR 0xfffff43A      /* Port J Pull-Up enb. reg */
#define PJSEL_ADDR  0xfffff43B      /* Port J Select Register */

#define PJDIR       BYTE_REF(PJDIR_ADDR)
#define PJDATA      BYTE_REF(PJDATA_ADDR)
#define PJPUEN      BYTE_REF(PJPUEN_ADDR)
#define PJSEL       BYTE_REF(PJSEL_ADDR)

#define PJ(x)       (1 << (x))

/*
 * Port K
 */
#define PKDIR_ADDR  0xfffff440      /* Port K direction reg */
#define PKDATA_ADDR 0xfffff441      /* Port K data register */
#define PKPUEN_ADDR 0xfffff442      /* Port K Pull-Up enb. reg */
#define PKSEL_ADDR  0xfffff443      /* Port K Select Register */

#define PKDIR       BYTE_REF(PKDIR_ADDR)
#define PKDATA      BYTE_REF(PKDATA_ADDR)
#define PKPUEN      BYTE_REF(PKPUEN_ADDR)
#define PKSEL       BYTE_REF(PKSEL_ADDR)

#define PK(x)       (1 << (x))

#define PK_DATAREADY        0x01    /* Use ~DATA_READY  as PK[0] */
#define PK_PWM2     0x01    /* Use PWM2  as PK[0] */
#define PK_R_W      0x02    /* Use R/W  as PK[1] */
#define PK_LDS      0x04    /* Use /LDS  as PK[2] */
#define PK_UDS      0x08    /* Use /UDS  as PK[3] */
#define PK_LD4      0x10    /* Use LD4 as PK[4] */
#define PK_LD5      0x20    /* Use LD5  as PK[5] */
#define PK_LD6      0x40    /* Use LD6 as PK[6] */
#define PK_LD7      0x80    /* Use LD7 as PK[7] */

#define PJDIR_ADDR  0xfffff438      /* Port J direction reg */
#define PJDATA_ADDR 0xfffff439      /* Port J data register */
#define PJPUEN_ADDR 0xfffff43A      /* Port J Pull-Up enable reg */
#define PJSEL_ADDR  0xfffff43B      /* Port J Select Register */

#define PJDIR       BYTE_REF(PJDIR_ADDR)
#define PJDATA      BYTE_REF(PJDATA_ADDR)
#define PJPUEN      BYTE_REF(PJPUEN_ADDR)
#define PJSEL       BYTE_REF(PJSEL_ADDR)

#define PJ(x)       (1 << (x))

#define PJ_MOSI     0x01    /* Use MOSI       as PJ[0] */
#define PJ_MISO     0x02    /* Use MISO       as PJ[1] */
#define PJ_SPICLK1      0x04    /* Use SPICLK1    as PJ[2] */
#define PJ_SS       0x08    /* Use SS         as PJ[3] */
#define PJ_RXD2         0x10    /* Use RXD2       as PJ[4] */
#define PJ_TXD2     0x20    /* Use TXD2       as PJ[5] */
#define PJ_RTS2     0x40    /* Use RTS2       as PJ[5] */
#define PJ_CTS2     0x80    /* Use CTS2       as PJ[5] */

/*
 * Port M
 */
#define PMDIR_ADDR  0xfffff448      /* Port M direction reg */
#define PMDATA_ADDR 0xfffff449      /* Port M data register */
#define PMPUEN_ADDR 0xfffff44a      /* Port M Pull-Up enable reg */
#define PMSEL_ADDR  0xfffff44b      /* Port M Select Register */

#define PMDIR       BYTE_REF(PMDIR_ADDR)
#define PMDATA      BYTE_REF(PMDATA_ADDR)
#define PMPUEN      BYTE_REF(PMPUEN_ADDR)
#define PMSEL       BYTE_REF(PMSEL_ADDR)

#define PM(x)       (1 << (x))

#define PM_SDCLK    0x01    /* Use SDCLK      as PM[0] */
#define PM_SDCE     0x02    /* Use SDCE       as PM[1] */
#define PM_DQMH     0x04    /* Use DQMH       as PM[2] */
#define PM_DQML     0x08    /* Use DQML       as PM[3] */
#define PM_SDA10        0x10    /* Use SDA10      as PM[4] */
#define PM_DMOE     0x20    /* Use DMOE       as PM[5] */

/**********
 *
 * 0xFFFFF5xx -- Pulse-Width Modulator (PWM)
 *
 **********/

/*
 * PWM Control Register
 */
#define PWMC_ADDR   0xfffff500
#define PWMC        WORD_REF(PWMC_ADDR)

#define PWMC_CLKSEL_MASK    0x0003  /* Clock Selection */
#define PWMC_CLKSEL_SHIFT   0
#define PWMC_REPEAT_MASK    0x000c  /* Sample Repeats */
#define PWMC_REPEAT_SHIFT   2
#define PWMC_EN         0x0010  /* Enable PWM */
#define PMNC_FIFOAV     0x0020  /* FIFO Available */
#define PWMC_IRQEN      0x0040  /* Interrupt Request Enable */
#define PWMC_IRQ        0x0080  /* Interrupt Request (FIFO empty) */
#define PWMC_PRESCALER_MASK 0x7f00  /* Incoming Clock prescaler */
#define PWMC_PRESCALER_SHIFT    8
#define PWMC_CLKSRC     0x8000  /* Clock Source Select */

/* '328-compatible definitions */
#define PWMC_PWMEN  PWMC_EN

/*
 * PWM Sample Register 
 */
#define PWMS_ADDR   0xfffff502
#define PWMS        WORD_REF(PWMS_ADDR)

/*
 * PWM Period Register
 */
#define PWMP_ADDR   0xfffff504
#define PWMP        BYTE_REF(PWMP_ADDR)

/*
 * PWM Counter Register
 */
#define PWMCNT_ADDR 0xfffff505
#define PWMCNT      BYTE_REF(PWMCNT_ADDR)

/**********
 *
 * 0xFFFFF6xx -- General-Purpose Timer
 *
 **********/

/* 
 * Timer Control register
 */
#define TCTL_ADDR   0xfffff600
#define TCTL        WORD_REF(TCTL_ADDR)

#define TCTL_TEN        0x0001  /* Timer Enable  */
#define TCTL_CLKSOURCE_MASK     0x000e  /* Clock Source: */
#define   TCTL_CLKSOURCE_STOP      0x0000   /* Stop count (disabled)    */
#define   TCTL_CLKSOURCE_SYSCLK    0x0002   /* SYSCLK to prescaler      */
#define   TCTL_CLKSOURCE_SYSCLK_16 0x0004   /* SYSCLK/16 to prescaler   */
#define   TCTL_CLKSOURCE_TIN       0x0006   /* TIN to prescaler         */
#define   TCTL_CLKSOURCE_32KHZ     0x0008   /* 32kHz clock to prescaler */
#define TCTL_IRQEN      0x0010  /* IRQ Enable    */
#define TCTL_OM         0x0020  /* Output Mode   */
#define TCTL_CAP_MASK       0x00c0  /* Capture Edge: */
#define   TCTL_CAP_RE       0x0040      /* Capture on rizing edge   */
#define   TCTL_CAP_FE       0x0080      /* Capture on falling edge  */
#define TCTL_FRR        0x0010  /* Free-Run Mode */

/* '328-compatible definitions */
#define TCTL1_ADDR  TCTL_ADDR
#define TCTL1       TCTL

/*
 * Timer Prescaler Register
 */
#define TPRER_ADDR  0xfffff602
#define TPRER       WORD_REF(TPRER_ADDR)

/* '328-compatible definitions */
#define TPRER1_ADDR TPRER_ADDR
#define TPRER1      TPRER

/*
 * Timer Compare Register
 */
#define TCMP_ADDR   0xfffff604
#define TCMP        WORD_REF(TCMP_ADDR)

/* '328-compatible definitions */
#define TCMP1_ADDR  TCMP_ADDR
#define TCMP1       TCMP

/*
 * Timer Capture register
 */
#define TCR_ADDR    0xfffff606
#define TCR     WORD_REF(TCR_ADDR)

/* '328-compatible definitions */
#define TCR1_ADDR   TCR_ADDR
#define TCR1        TCR

/*
 * Timer Counter Register
 */
#define TCN_ADDR    0xfffff608
#define TCN     WORD_REF(TCN_ADDR)

/* '328-compatible definitions */
#define TCN1_ADDR   TCN_ADDR
#define TCN1        TCN

/*
 * Timer Status Register
 */
#define TSTAT_ADDR  0xfffff60a
#define TSTAT       WORD_REF(TSTAT_ADDR)

#define TSTAT_COMP  0x0001      /* Compare Event occurred */
#define TSTAT_CAPT  0x0001      /* Capture Event occurred */

/* '328-compatible definitions */
#define TSTAT1_ADDR TSTAT_ADDR
#define TSTAT1      TSTAT

/**********
 *
 * 0xFFFFF8xx -- Serial Periferial Interface Master (SPIM)
 *
 **********/

/*
 * SPIM Data Register
 */
#define SPIMDATA_ADDR   0xfffff800
#define SPIMDATA    WORD_REF(SPIMDATA_ADDR)

/*
 * SPIM Control/Status Register
 */
#define SPIMCONT_ADDR   0xfffff802
#define SPIMCONT    WORD_REF(SPIMCONT_ADDR)

#define SPIMCONT_BIT_COUNT_MASK  0x000f /* Transfer Length in Bytes */
#define SPIMCONT_BIT_COUNT_SHIFT 0
#define SPIMCONT_POL         0x0010 /* SPMCLK Signel Polarity */
#define SPIMCONT_PHA         0x0020 /* Clock/Data phase relationship */
#define SPIMCONT_IRQEN       0x0040 /* IRQ Enable */
#define SPIMCONT_IRQ         0x0080 /* Interrupt Request */
#define SPIMCONT_XCH         0x0100 /* Exchange */
#define SPIMCONT_ENABLE      0x0200 /* Enable SPIM */
#define SPIMCONT_DATA_RATE_MASK  0xe000 /* SPIM Data Rate */
#define SPIMCONT_DATA_RATE_SHIFT 13

/* '328-compatible definitions */
#define SPIMCONT_SPIMIRQ    SPIMCONT_IRQ
#define SPIMCONT_SPIMEN     SPIMCONT_ENABLE

/**********
 *
 * 0xFFFFF9xx -- UART
 *
 **********/

/*
 * UART Status/Control Register
 */

#define USTCNT_ADDR 0xfffff900
#define USTCNT      WORD_REF(USTCNT_ADDR)

#define USTCNT_TXAE 0x0001  /* Transmitter Available Interrupt Enable */
#define USTCNT_TXHE 0x0002  /* Transmitter Half Empty Enable */
#define USTCNT_TXEE 0x0004  /* Transmitter Empty Interrupt Enable */
#define USTCNT_RXRE 0x0008  /* Receiver Ready Interrupt Enable */
#define USTCNT_RXHE 0x0010  /* Receiver Half-Full Interrupt Enable */
#define USTCNT_RXFE 0x0020  /* Receiver Full Interrupt Enable */
#define USTCNT_CTSD 0x0040  /* CTS Delta Interrupt Enable */
#define USTCNT_ODEN 0x0080  /* Old Data Interrupt Enable */
#define USTCNT_8_7  0x0100  /* Eight or seven-bit transmission */
#define USTCNT_STOP 0x0200  /* Stop bit transmission */
#define USTCNT_ODD  0x0400  /* Odd Parity */
#define USTCNT_PEN  0x0800  /* Parity Enable */
#define USTCNT_CLKM 0x1000  /* Clock Mode Select */
#define USTCNT_TXEN 0x2000  /* Transmitter Enable */
#define USTCNT_RXEN 0x4000  /* Receiver Enable */
#define USTCNT_UEN  0x8000  /* UART Enable */

/* '328-compatible definitions */
#define USTCNT_TXAVAILEN    USTCNT_TXAE
#define USTCNT_TXHALFEN     USTCNT_TXHE
#define USTCNT_TXEMPTYEN    USTCNT_TXEE
#define USTCNT_RXREADYEN    USTCNT_RXRE
#define USTCNT_RXHALFEN     USTCNT_RXHE
#define USTCNT_RXFULLEN     USTCNT_RXFE
#define USTCNT_CTSDELTAEN   USTCNT_CTSD
#define USTCNT_ODD_EVEN     USTCNT_ODD
#define USTCNT_PARITYEN     USTCNT_PEN
#define USTCNT_CLKMODE      USTCNT_CLKM
#define USTCNT_UARTEN       USTCNT_UEN

/*
 * UART Baud Control Register
 */
#define UBAUD_ADDR  0xfffff902
#define UBAUD       WORD_REF(UBAUD_ADDR)

#define UBAUD_PRESCALER_MASK    0x003f  /* Actual divisor is 65 - PRESCALER */
#define UBAUD_PRESCALER_SHIFT   0
#define UBAUD_DIVIDE_MASK   0x0700  /* Baud Rate freq. divizor */
#define UBAUD_DIVIDE_SHIFT  8
#define UBAUD_BAUD_SRC      0x0800  /* Baud Rate Source */
#define UBAUD_UCLKDIR       0x2000  /* UCLK Direction */

/*
 * UART Receiver Register 
 */
#define URX_ADDR    0xfffff904
#define URX     WORD_REF(URX_ADDR)

#define URX_RXDATA_ADDR 0xfffff905
#define URX_RXDATA  BYTE_REF(URX_RXDATA_ADDR)

#define URX_RXDATA_MASK  0x00ff /* Received data */
#define URX_RXDATA_SHIFT 0
#define URX_PARITY_ERROR 0x0100 /* Parity Error */
#define URX_BREAK    0x0200 /* Break Detected */
#define URX_FRAME_ERROR  0x0400 /* Framing Error */
#define URX_OVRUN    0x0800 /* Serial Overrun */
#define URX_OLD_DATA     0x1000 /* Old data in FIFO */
#define URX_DATA_READY   0x2000 /* Data Ready (FIFO not empty) */
#define URX_FIFO_HALF    0x4000 /* FIFO is Half-Full */
#define URX_FIFO_FULL    0x8000 /* FIFO is Full */

/*
 * UART Transmitter Register 
 */
#define UTX_ADDR    0xfffff906
#define UTX     WORD_REF(UTX_ADDR)

#define UTX_TXDATA_ADDR 0xfffff907
#define UTX_TXDATA  BYTE_REF(UTX_TXDATA_ADDR)

#define UTX_TXDATA_MASK  0x00ff /* Data to be transmitted */
#define UTX_TXDATA_SHIFT 0
#define UTX_CTS_DELTA    0x0100 /* CTS changed */
#define UTX_CTS_STAT     0x0200 /* CTS State */
#define UTX_BUSY     0x0400 /* FIFO is busy, sending a character */
#define UTX_NOCTS    0x0800 /* Ignore CTS */
#define UTX_SEND_BREAK   0x1000 /* Send a BREAK */
#define UTX_TX_AVAIL     0x2000 /* Transmit FIFO has a slot available */
#define UTX_FIFO_HALF    0x4000 /* Transmit FIFO is half empty */
#define UTX_FIFO_EMPTY   0x8000 /* Transmit FIFO is empty */

/* '328-compatible definitions */
#define UTX_CTS_STATUS  UTX_CTS_STAT
#define UTX_IGNORE_CTS  UTX_NOCTS

/*
 * UART Miscellaneous Register 
 */
#define UMISC_ADDR  0xfffff908
#define UMISC       WORD_REF(UMISC_ADDR)

#define UMISC_TX_POL     0x0004 /* Transmit Polarity */
#define UMISC_RX_POL     0x0008 /* Receive Polarity */
#define UMISC_IRDA_LOOP  0x0010 /* IrDA Loopback Enable */
#define UMISC_IRDA_EN    0x0020 /* Infra-Red Enable */
#define UMISC_RTS    0x0040 /* Set RTS status */
#define UMISC_RTSCONT    0x0080 /* Choose RTS control */
#define UMISC_IR_TEST    0x0400 /* IRDA Test Enable */
#define UMISC_BAUD_RESET 0x0800 /* Reset Baud Rate Generation Counters */
#define UMISC_LOOP   0x1000 /* Serial Loopback Enable */
#define UMISC_FORCE_PERR 0x2000 /* Force Parity Error */
#define UMISC_CLKSRC     0x4000 /* Clock Source */
#define UMISC_BAUD_TEST  0x8000 /* Enable Baud Test Mode */

/* 
 * UART Non-integer Prescaler Register
 */
#define NIPR_ADDR   0xfffff90a
#define NIPR        WORD_REF(NIPR_ADDR)

#define NIPR_STEP_VALUE_MASK    0x00ff  /* NI prescaler step value */
#define NIPR_STEP_VALUE_SHIFT   0
#define NIPR_SELECT_MASK    0x0700  /* Tap Selection */
#define NIPR_SELECT_SHIFT   8
#define NIPR_PRE_SEL        0x8000  /* Non-integer prescaler select */


/* generalization of uart control registers to support multiple ports: */
typedef struct {
  volatile unsigned short int ustcnt;
  volatile unsigned short int ubaud;
  union {
    volatile unsigned short int w;
    struct {
      volatile unsigned char status;
      volatile unsigned char rxdata;
    } b;
  } urx;
  union {
    volatile unsigned short int w;
    struct {
      volatile unsigned char status;
      volatile unsigned char txdata;
    } b;
  } utx;
  volatile unsigned short int umisc;
  volatile unsigned short int nipr;
  volatile unsigned short int hmark;
  volatile unsigned short int unused;
} __attribute__((packed)) m68328_uart;




/**********
 *
 * 0xFFFFFAxx -- LCD Controller
 *
 **********/

/*
 * LCD Screen Starting Address Register 
 */
#define LSSA_ADDR   0xfffffa00
#define LSSA        LONG_REF(LSSA_ADDR)

#define LSSA_SSA_MASK   0x1ffffffe  /* Bits 0 and 29-31 are reserved */

/*
 * LCD Virtual Page Width Register 
 */
#define LVPW_ADDR   0xfffffa05
#define LVPW        BYTE_REF(LVPW_ADDR)

/*
 * LCD Screen Width Register (not compatible with '328 !!!) 
 */
#define LXMAX_ADDR  0xfffffa08
#define LXMAX       WORD_REF(LXMAX_ADDR)

#define LXMAX_XM_MASK   0x02f0      /* Bits 0-3 and 10-15 are reserved */

/*
 * LCD Screen Height Register
 */
#define LYMAX_ADDR  0xfffffa0a
#define LYMAX       WORD_REF(LYMAX_ADDR)

#define LYMAX_YM_MASK   0x01ff      /* Bits 9-15 are reserved */

/*
 * LCD Cursor X Position Register
 */
#define LCXP_ADDR   0xfffffa18
#define LCXP        WORD_REF(LCXP_ADDR)

#define LCXP_CC_MASK    0xc000      /* Cursor Control */
#define   LCXP_CC_TRAMSPARENT   0x0000
#define   LCXP_CC_BLACK     0x4000
#define   LCXP_CC_REVERSED  0x8000
#define   LCXP_CC_WHITE     0xc000
#define LCXP_CXP_MASK   0x02ff      /* Cursor X position */

/*
 * LCD Cursor Y Position Register
 */
#define LCYP_ADDR   0xfffffa1a
#define LCYP        WORD_REF(LCYP_ADDR)

#define LCYP_CYP_MASK   0x01ff      /* Cursor Y Position */

/*
 * LCD Cursor Width and Heigth Register
 */
#define LCWCH_ADDR  0xfffffa1c
#define LCWCH       WORD_REF(LCWCH_ADDR)

#define LCWCH_CH_MASK   0x001f      /* Cursor Height */
#define LCWCH_CH_SHIFT  0
#define LCWCH_CW_MASK   0x1f00      /* Cursor Width */
#define LCWCH_CW_SHIFT  8

/*
 * LCD Blink Control Register
 */
#define LBLKC_ADDR  0xfffffa1f
#define LBLKC       BYTE_REF(LBLKC_ADDR)

#define LBLKC_BD_MASK   0x7f    /* Blink Divisor */
#define LBLKC_BD_SHIFT  0
#define LBLKC_BKEN  0x80    /* Blink Enabled */

/*
 * LCD Panel Interface Configuration Register 
 */
#define LPICF_ADDR  0xfffffa20
#define LPICF       BYTE_REF(LPICF_ADDR)

#define LPICF_GS_MASK    0x03    /* Gray-Scale Mode */
#define   LPICF_GS_BW      0x00
#define   LPICF_GS_GRAY_4  0x01
#define   LPICF_GS_GRAY_16 0x02
#define LPICF_PBSIZ_MASK 0x0c   /* Panel Bus Width */
#define   LPICF_PBSIZ_1    0x00
#define   LPICF_PBSIZ_2    0x04
#define   LPICF_PBSIZ_4    0x08

/*
 * LCD Polarity Configuration Register 
 */
#define LPOLCF_ADDR 0xfffffa21
#define LPOLCF      BYTE_REF(LPOLCF_ADDR)

#define LPOLCF_PIXPOL   0x01    /* Pixel Polarity */
#define LPOLCF_LPPOL    0x02    /* Line Pulse Polarity */
#define LPOLCF_FLMPOL   0x04    /* Frame Marker Polarity */
#define LPOLCF_LCKPOL   0x08    /* LCD Shift Lock Polarity */

/*
 * LACD (LCD Alternate Crystal Direction) Rate Control Register
 */
#define LACDRC_ADDR 0xfffffa23
#define LACDRC      BYTE_REF(LACDRC_ADDR)

#define LACDRC_ACDSLT    0x80   /* Signal Source Select */
#define LACDRC_ACD_MASK  0x0f   /* Alternate Crystal Direction Control */
#define LACDRC_ACD_SHIFT 0

/*
 * LCD Pixel Clock Divider Register
 */
#define LPXCD_ADDR  0xfffffa25
#define LPXCD       BYTE_REF(LPXCD_ADDR)

#define LPXCD_PCD_MASK  0x3f    /* Pixel Clock Divider */
#define LPXCD_PCD_SHIFT 0

/*
 * LCD Clocking Control Register
 */
#define LCKCON_ADDR 0xfffffa27
#define LCKCON      BYTE_REF(LCKCON_ADDR)

#define LCKCON_DWS_MASK  0x0f   /* Display Wait-State */
#define LCKCON_DWS_SHIFT 0
#define LCKCON_DWIDTH    0x40   /* Display Memory Width  */
#define LCKCON_LCDON     0x80   /* Enable LCD Controller */

/* '328-compatible definitions */
#define LCKCON_DW_MASK  LCKCON_DWS_MASK
#define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT
 
/*
 * LCD Refresh Rate Adjustment Register 
 */
#define LRRA_ADDR   0xfffffa29
#define LRRA        BYTE_REF(LRRA_ADDR)

/*
 * LCD Panning Offset Register
 */
#define LPOSR_ADDR  0xfffffa2d
#define LPOSR       BYTE_REF(LPOSR_ADDR)

#define LPOSR_POS_MASK  0x0f    /* Pixel Offset Code */
#define LPOSR_POS_SHIFT 0

/*
 * LCD Frame Rate Control Modulation Register
 */
#define LFRCM_ADDR  0xfffffa31
#define LFRCM       BYTE_REF(LFRCM_ADDR)

#define LFRCM_YMOD_MASK  0x0f   /* Vertical Modulation */
#define LFRCM_YMOD_SHIFT 0
#define LFRCM_XMOD_MASK  0xf0   /* Horizontal Modulation */
#define LFRCM_XMOD_SHIFT 4

/*
 * LCD Gray Palette Mapping Register
 */
#define LGPMR_ADDR  0xfffffa33
#define LGPMR       BYTE_REF(LGPMR_ADDR)

#define LGPMR_G1_MASK   0x0f
#define LGPMR_G1_SHIFT  0
#define LGPMR_G2_MASK   0xf0
#define LGPMR_G2_SHIFT  4

/* 
 * PWM Contrast Control Register
 */
#define PWMR_ADDR   0xfffffa36
#define PWMR        WORD_REF(PWMR_ADDR)

#define PWMR_PW_MASK    0x00ff  /* Pulse Width */
#define PWMR_PW_SHIFT   0
#define PWMR_CCPEN  0x0100  /* Contrast Control Enable */
#define PWMR_SRC_MASK   0x0600  /* Input Clock Source */
#define   PWMR_SRC_LINE   0x0000    /* Line Pulse  */
#define   PWMR_SRC_PIXEL  0x0200    /* Pixel Clock */
#define   PWMR_SRC_LCD    0x4000    /* LCD clock   */

/**********
 *
 * 0xFFFFFBxx -- Real-Time Clock (RTC)
 *
 **********/

/*
 * RTC Hours Minutes and Seconds Register
 */
#define RTCTIME_ADDR    0xfffffb00
#define RTCTIME     LONG_REF(RTCTIME_ADDR)

#define RTCTIME_SECONDS_MASK    0x0000003f  /* Seconds */
#define RTCTIME_SECONDS_SHIFT   0
#define RTCTIME_MINUTES_MASK    0x003f0000  /* Minutes */
#define RTCTIME_MINUTES_SHIFT   16
#define RTCTIME_HOURS_MASK  0x1f000000  /* Hours */
#define RTCTIME_HOURS_SHIFT 24

/*
 *  RTC Alarm Register 
 */
#define RTCALRM_ADDR    0xfffffb04
#define RTCALRM         LONG_REF(RTCALRM_ADDR)

#define RTCALRM_SECONDS_MASK    0x0000003f      /* Seconds */
#define RTCALRM_SECONDS_SHIFT   0
#define RTCALRM_MINUTES_MASK    0x003f0000      /* Minutes */
#define RTCALRM_MINUTES_SHIFT   16
#define RTCALRM_HOURS_MASK      0x1f000000      /* Hours */
#define RTCALRM_HOURS_SHIFT     24

/*
 * Watchdog Timer Register 
 */
#define WATCHDOG_ADDR   0xfffffb0a
#define WATCHDOG    WORD_REF(WATCHDOG_ADDR)

#define WATCHDOG_EN 0x0001  /* Watchdog Enabled */
#define WATCHDOG_ISEL   0x0002  /* Select the watchdog interrupt */
#define WATCHDOG_INTF   0x0080  /* Watchdog interrupt occurred */
#define WATCHDOG_CNT_MASK  0x0300   /* Watchdog Counter */
#define WATCHDOG_CNT_SHIFT 8

/*
 * RTC Control Register
 */
#define RTCCTL_ADDR 0xfffffb0c
#define RTCCTL      WORD_REF(RTCCTL_ADDR)

#define RTCCTL_XTL  0x0020  /* Crystal Selection */
#define RTCCTL_EN   0x0080  /* RTC Enable */

/* '328-compatible definitions */
#define RTCCTL_384  RTCCTL_XTL
#define RTCCTL_ENABLE   RTCCTL_EN

/*
 * RTC Interrupt Status Register 
 */
#define RTCISR_ADDR 0xfffffb0e
#define RTCISR      WORD_REF(RTCISR_ADDR)

#define RTCISR_SW   0x0001  /* Stopwatch timed out */
#define RTCISR_MIN  0x0002  /* 1-minute interrupt has occurred */
#define RTCISR_ALM  0x0004  /* Alarm interrupt has occurred */
#define RTCISR_DAY  0x0008  /* 24-hour rollover interrupt has occurred */
#define RTCISR_1HZ  0x0010  /* 1Hz interrupt has occurred */
#define RTCISR_HR   0x0020  /* 1-hour interrupt has occurred */
#define RTCISR_SAM0 0x0100  /*   4Hz /   4.6875Hz interrupt has occurred */ 
#define RTCISR_SAM1 0x0200  /*   8Hz /   9.3750Hz interrupt has occurred */ 
#define RTCISR_SAM2 0x0400  /*  16Hz /  18.7500Hz interrupt has occurred */ 
#define RTCISR_SAM3 0x0800  /*  32Hz /  37.5000Hz interrupt has occurred */ 
#define RTCISR_SAM4 0x1000  /*  64Hz /  75.0000Hz interrupt has occurred */ 
#define RTCISR_SAM5 0x2000  /* 128Hz / 150.0000Hz interrupt has occurred */ 
#define RTCISR_SAM6 0x4000  /* 256Hz / 300.0000Hz interrupt has occurred */ 
#define RTCISR_SAM7 0x8000  /* 512Hz / 600.0000Hz interrupt has occurred */ 

/*
 * RTC Interrupt Enable Register
 */
#define RTCIENR_ADDR    0xfffffb10
#define RTCIENR     WORD_REF(RTCIENR_ADDR)

#define RTCIENR_SW  0x0001  /* Stopwatch interrupt enable */
#define RTCIENR_MIN 0x0002  /* 1-minute interrupt enable */
#define RTCIENR_ALM 0x0004  /* Alarm interrupt enable */
#define RTCIENR_DAY 0x0008  /* 24-hour rollover interrupt enable */
#define RTCIENR_1HZ 0x0010  /* 1Hz interrupt enable */
#define RTCIENR_HR  0x0020  /* 1-hour interrupt enable */
#define RTCIENR_SAM0    0x0100  /*   4Hz /   4.6875Hz interrupt enable */ 
#define RTCIENR_SAM1    0x0200  /*   8Hz /   9.3750Hz interrupt enable */ 
#define RTCIENR_SAM2    0x0400  /*  16Hz /  18.7500Hz interrupt enable */ 
#define RTCIENR_SAM3    0x0800  /*  32Hz /  37.5000Hz interrupt enable */ 
#define RTCIENR_SAM4    0x1000  /*  64Hz /  75.0000Hz interrupt enable */ 
#define RTCIENR_SAM5    0x2000  /* 128Hz / 150.0000Hz interrupt enable */ 
#define RTCIENR_SAM6    0x4000  /* 256Hz / 300.0000Hz interrupt enable */ 
#define RTCIENR_SAM7    0x8000  /* 512Hz / 600.0000Hz interrupt enable */ 

/* 
 * Stopwatch Minutes Register
 */
#define STPWCH_ADDR 0xfffffb12
#define STPWCH      WORD_REF(STPWCH_ADDR)

#define STPWCH_CNT_MASK  0x003f /* Stopwatch countdown value */
#define SPTWCH_CNT_SHIFT 0

/*
 * RTC Day Count Register 
 */
#define DAYR_ADDR   0xfffffb1a
#define DAYR        WORD_REF(DAYR_ADDR)

#define DAYR_DAYS_MASK  0x1ff   /* Day Setting */
#define DAYR_DAYS_SHIFT 0

/*
 * RTC Day Alarm Register 
 */
#define DAYALARM_ADDR   0xfffffb1c
#define DAYALARM    WORD_REF(DAYALARM_ADDR)

#define DAYALARM_DAYSAL_MASK    0x01ff  /* Day Setting of the Alarm */
#define DAYALARM_DAYSAL_SHIFT   0

/**********
 *
 * 0xFFFFFCxx -- DRAM Controller
 *
 **********/

/*
 * DRAM Memory Configuration Register 
 */
#define DRAMMC_ADDR 0xfffffc00
#define DRAMMC      WORD_REF(DRAMMC_ADDR)

#define DRAMMC_ROW12_MASK   0xc000  /* Row address bit for MD12 */
#define   DRAMMC_ROW12_PA10 0x0000
#define   DRAMMC_ROW12_PA21 0x4000  
#define   DRAMMC_ROW12_PA23 0x8000
#define DRAMMC_ROW0_MASK    0x3000  /* Row address bit for MD0 */
#define   DRAMMC_ROW0_PA11  0x0000
#define   DRAMMC_ROW0_PA22  0x1000
#define   DRAMMC_ROW0_PA23  0x2000
#define DRAMMC_ROW11        0x0800  /* Row address bit for MD11 PA20/PA22 */
#define DRAMMC_ROW10        0x0400  /* Row address bit for MD10 PA19/PA21 */
#define DRAMMC_ROW9     0x0200  /* Row address bit for MD9  PA9/PA19  */
#define DRAMMC_ROW8     0x0100  /* Row address bit for MD8  PA10/PA20 */
#define DRAMMC_COL10        0x0080  /* Col address bit for MD10 PA11/PA0  */
#define DRAMMC_COL9     0x0040  /* Col address bit for MD9  PA10/PA0  */
#define DRAMMC_COL8     0x0020  /* Col address bit for MD8  PA9/PA0   */
#define DRAMMC_REF_MASK     0x001f  /* Reresh Cycle */
#define DRAMMC_REF_SHIFT    0

/*
 * DRAM Control Register
 */
#define DRAMC_ADDR  0xfffffc02
#define DRAMC       WORD_REF(DRAMC_ADDR)

#define DRAMC_DWE      0x0001   /* DRAM Write Enable */
#define DRAMC_RST      0x0002   /* Reset Burst Refresh Enable */
#define DRAMC_LPR      0x0004   /* Low-Power Refresh Enable */
#define DRAMC_SLW      0x0008   /* Slow RAM */
#define DRAMC_LSP      0x0010   /* Light Sleep */
#define DRAMC_MSW      0x0020   /* Slow Multiplexing */
#define DRAMC_WS_MASK      0x00c0   /* Wait-states */
#define DRAMC_WS_SHIFT     6
#define DRAMC_PGSZ_MASK    0x0300   /* Page Size for fast page mode */
#define DRAMC_PGSZ_SHIFT   8
#define   DRAMC_PGSZ_256K  0x0000   
#define   DRAMC_PGSZ_512K  0x0100
#define   DRAMC_PGSZ_1024K 0x0200
#define   DRAMC_PGSZ_2048K 0x0300
#define DRAMC_EDO      0x0400   /* EDO DRAM */
#define DRAMC_CLK      0x0800   /* Refresh Timer Clock source select */
#define DRAMC_BC_MASK      0x3000   /* Page Access Clock Cycle (FP mode) */
#define DRAMC_BC_SHIFT     12
#define DRAMC_RM       0x4000   /* Refresh Mode */
#define DRAMC_EN       0x8000   /* DRAM Controller enable */


/**********
 *
 * 0xFFFFFDxx -- In-Circuit Emulation (ICE)
 *
 **********/

/*
 * ICE Module Address Compare Register
 */
#define ICEMACR_ADDR    0xfffffd00
#define ICEMACR     LONG_REF(ICEMACR_ADDR)

/*
 * ICE Module Address Mask Register
 */
#define ICEMAMR_ADDR    0xfffffd04
#define ICEMAMR     LONG_REF(ICEMAMR_ADDR)

/*
 * ICE Module Control Compare Register
 */
#define ICEMCCR_ADDR    0xfffffd08
#define ICEMCCR     WORD_REF(ICEMCCR_ADDR)

#define ICEMCCR_PD  0x0001  /* Program/Data Cycle Selection */
#define ICEMCCR_RW  0x0002  /* Read/Write Cycle Selection */

/*
 * ICE Module Control Mask Register
 */
#define ICEMCMR_ADDR    0xfffffd0a
#define ICEMCMR     WORD_REF(ICEMCMR_ADDR)

#define ICEMCMR_PDM 0x0001  /* Program/Data Cycle Mask */
#define ICEMCMR_RWM 0x0002  /* Read/Write Cycle Mask */

/*
 * ICE Module Control Register 
 */
#define ICEMCR_ADDR 0xfffffd0c
#define ICEMCR      WORD_REF(ICEMCR_ADDR)

#define ICEMCR_CEN  0x0001  /* Compare Enable */
#define ICEMCR_PBEN 0x0002  /* Program Break Enable */
#define ICEMCR_SB   0x0004  /* Single Breakpoint */
#define ICEMCR_HMDIS    0x0008  /* HardMap disable */
#define ICEMCR_BBIEN    0x0010  /* Bus Break Interrupt Enable */

/*
 * ICE Module Status Register 
 */
#define ICEMSR_ADDR 0xfffffd0e
#define ICEMSR      WORD_REF(ICEMSR_ADDR)

#define ICEMSR_EMUEN    0x0001  /* Emulation Enable */
#define ICEMSR_BRKIRQ   0x0002  /* A-Line Vector Fetch Detected */
#define ICEMSR_BBIRQ    0x0004  /* Bus Break Interrupt Detected */
#define ICEMSR_EMIRQ    0x0008  /* EMUIRQ Falling Edge Detected */

#endif /* _MC68VZ328_H_ */