apbuart.h

Go to the documentation of this file.

#ifndef __GRLIB_APBUART_H__
#define __GRLIB_APBUART_H__

#include <asm/io.h>

#define UART_NR     8
static int grlib_apbuart_port_nr;

struct grlib_apbuart_regs_map {
    u32 data;
    u32 status;
    u32 ctrl;
    u32 scaler;
};

struct amba_prom_registers {
    unsigned int phys_addr;
    unsigned int reg_size;
};

/*
 *  The following defines the bits in the APBUART Status Registers.
 */
#define UART_STATUS_DR   0x00000001 /* Data Ready */
#define UART_STATUS_TSE  0x00000002 /* TX Send Register Empty */
#define UART_STATUS_THE  0x00000004 /* TX Hold Register Empty */
#define UART_STATUS_BR   0x00000008 /* Break Error */
#define UART_STATUS_OE   0x00000010 /* RX Overrun Error */
#define UART_STATUS_PE   0x00000020 /* RX Parity Error */
#define UART_STATUS_FE   0x00000040 /* RX Framing Error */
#define UART_STATUS_ERR  0x00000078 /* Error Mask */

/*
 *  The following defines the bits in the APBUART Ctrl Registers.
 */
#define UART_CTRL_RE     0x00000001 /* Receiver enable */
#define UART_CTRL_TE     0x00000002 /* Transmitter enable */
#define UART_CTRL_RI     0x00000004 /* Receiver interrupt enable */
#define UART_CTRL_TI     0x00000008 /* Transmitter irq */
#define UART_CTRL_PS     0x00000010 /* Parity select */
#define UART_CTRL_PE     0x00000020 /* Parity enable */
#define UART_CTRL_FL     0x00000040 /* Flow control enable */
#define UART_CTRL_LB     0x00000080 /* Loopback enable */

#define APBBASE(port) ((struct grlib_apbuart_regs_map *)((port)->membase))

#define APBBASE_DATA_P(port)    (&(APBBASE(port)->data))
#define APBBASE_STATUS_P(port)  (&(APBBASE(port)->status))
#define APBBASE_CTRL_P(port)    (&(APBBASE(port)->ctrl))
#define APBBASE_SCALAR_P(port)  (&(APBBASE(port)->scaler))

#define UART_GET_CHAR(port) (__raw_readl(APBBASE_DATA_P(port)))
#define UART_PUT_CHAR(port, v)  (__raw_writel(v, APBBASE_DATA_P(port)))
#define UART_GET_STATUS(port)   (__raw_readl(APBBASE_STATUS_P(port)))
#define UART_PUT_STATUS(port, v)(__raw_writel(v, APBBASE_STATUS_P(port)))
#define UART_GET_CTRL(port) (__raw_readl(APBBASE_CTRL_P(port)))
#define UART_PUT_CTRL(port, v)  (__raw_writel(v, APBBASE_CTRL_P(port)))
#define UART_GET_SCAL(port) (__raw_readl(APBBASE_SCALAR_P(port)))
#define UART_PUT_SCAL(port, v)  (__raw_writel(v, APBBASE_SCALAR_P(port)))

#define UART_RX_DATA(s)     (((s) & UART_STATUS_DR) != 0)
#define UART_TX_READY(s)    (((s) & UART_STATUS_THE) != 0)

#endif /* __GRLIB_APBUART_H__ */