Linux Kernel  3.7.1
 All Data Structures Namespaces Files Functions Variables Typedefs Enumerations Enumerator Macros Groups Pages
keylargo.h
Go to the documentation of this file.
1 #ifndef _ASM_POWERPC_KEYLARGO_H
2 #define _ASM_POWERPC_KEYLARGO_H
3 #ifdef __KERNEL__
4 /*
5  * keylargo.h: definitions for using the "KeyLargo" I/O controller chip.
6  *
7  */
8 
9 /* "Pangea" chipset has keylargo device-id 0x25 while core99
10  * has device-id 0x22. The rev. of the pangea one is 0, so we
11  * fake an artificial rev. in keylargo_rev by oring 0x100
12  */
13 #define KL_PANGEA_REV 0x100
14 
15 /* offset from base for feature control registers */
16 #define KEYLARGO_MBCR 0x34 /* KL Only, Media bay control/status */
17 #define KEYLARGO_FCR0 0x38
18 #define KEYLARGO_FCR1 0x3c
19 #define KEYLARGO_FCR2 0x40
20 #define KEYLARGO_FCR3 0x44
21 #define KEYLARGO_FCR4 0x48
22 #define KEYLARGO_FCR5 0x4c /* Pangea only */
23 
24 /* K2 additional FCRs */
25 #define K2_FCR6 0x34
26 #define K2_FCR7 0x30
27 #define K2_FCR8 0x2c
28 #define K2_FCR9 0x28
29 #define K2_FCR10 0x24
30 
31 /* GPIO registers */
32 #define KEYLARGO_GPIO_LEVELS0 0x50
33 #define KEYLARGO_GPIO_LEVELS1 0x54
34 #define KEYLARGO_GPIO_EXTINT_0 0x58
35 #define KEYLARGO_GPIO_EXTINT_CNT 18
36 #define KEYLARGO_GPIO_0 0x6A
37 #define KEYLARGO_GPIO_CNT 17
38 #define KEYLARGO_GPIO_EXTINT_DUAL_EDGE 0x80
39 #define KEYLARGO_GPIO_OUTPUT_ENABLE 0x04
40 #define KEYLARGO_GPIO_OUTOUT_DATA 0x01
41 #define KEYLARGO_GPIO_INPUT_DATA 0x02
42 
43 /* K2 does only extint GPIOs and does 51 of them */
44 #define K2_GPIO_EXTINT_0 0x58
45 #define K2_GPIO_EXTINT_CNT 51
46 
47 /* Specific GPIO regs */
48 
49 #define KL_GPIO_MODEM_RESET (KEYLARGO_GPIO_0+0x03)
50 #define KL_GPIO_MODEM_POWER (KEYLARGO_GPIO_0+0x02) /* Pangea */
51 
52 #define KL_GPIO_SOUND_POWER (KEYLARGO_GPIO_0+0x05)
53 
54 /* Hrm... this one is only to be used on Pismo. It seems to also
55  * control the timebase enable on other machines. Still to be
56  * experimented... --BenH.
57  */
58 #define KL_GPIO_FW_CABLE_POWER (KEYLARGO_GPIO_0+0x09)
59 #define KL_GPIO_TB_ENABLE (KEYLARGO_GPIO_0+0x09)
60 
61 #define KL_GPIO_ETH_PHY_RESET (KEYLARGO_GPIO_0+0x10)
62 
63 #define KL_GPIO_EXTINT_CPU1 (KEYLARGO_GPIO_0+0x0a)
64 #define KL_GPIO_EXTINT_CPU1_ASSERT 0x04
65 #define KL_GPIO_EXTINT_CPU1_RELEASE 0x38
66 
67 #define KL_GPIO_RESET_CPU0 (KEYLARGO_GPIO_EXTINT_0+0x03)
68 #define KL_GPIO_RESET_CPU1 (KEYLARGO_GPIO_EXTINT_0+0x04)
69 #define KL_GPIO_RESET_CPU2 (KEYLARGO_GPIO_EXTINT_0+0x0f)
70 #define KL_GPIO_RESET_CPU3 (KEYLARGO_GPIO_EXTINT_0+0x10)
71 
72 #define KL_GPIO_PMU_MESSAGE_IRQ (KEYLARGO_GPIO_EXTINT_0+0x09)
73 #define KL_GPIO_PMU_MESSAGE_BIT KEYLARGO_GPIO_INPUT_DATA
74 
75 #define KL_GPIO_MEDIABAY_IRQ (KEYLARGO_GPIO_EXTINT_0+0x0e)
76 
77 #define KL_GPIO_AIRPORT_0 (KEYLARGO_GPIO_EXTINT_0+0x0a)
78 #define KL_GPIO_AIRPORT_1 (KEYLARGO_GPIO_EXTINT_0+0x0d)
79 #define KL_GPIO_AIRPORT_2 (KEYLARGO_GPIO_0+0x0d)
80 #define KL_GPIO_AIRPORT_3 (KEYLARGO_GPIO_0+0x0e)
81 #define KL_GPIO_AIRPORT_4 (KEYLARGO_GPIO_0+0x0f)
82 
83 /*
84  * Bits in feature control register. Those bits different for K2 are
85  * listed separately
86  */
87 #define KL_MBCR_MB0_PCI_ENABLE 0x00000800 /* exist ? */
88 #define KL_MBCR_MB0_IDE_ENABLE 0x00001000
89 #define KL_MBCR_MB0_FLOPPY_ENABLE 0x00002000 /* exist ? */
90 #define KL_MBCR_MB0_SOUND_ENABLE 0x00004000 /* hrm... */
91 #define KL_MBCR_MB0_DEV_MASK 0x00007800
92 #define KL_MBCR_MB0_DEV_POWER 0x00000400
93 #define KL_MBCR_MB0_DEV_RESET 0x00000200
94 #define KL_MBCR_MB0_ENABLE 0x00000100
95 #define KL_MBCR_MB1_PCI_ENABLE 0x08000000 /* exist ? */
96 #define KL_MBCR_MB1_IDE_ENABLE 0x10000000
97 #define KL_MBCR_MB1_FLOPPY_ENABLE 0x20000000 /* exist ? */
98 #define KL_MBCR_MB1_SOUND_ENABLE 0x40000000 /* hrm... */
99 #define KL_MBCR_MB1_DEV_MASK 0x78000000
100 #define KL_MBCR_MB1_DEV_POWER 0x04000000
101 #define KL_MBCR_MB1_DEV_RESET 0x02000000
102 #define KL_MBCR_MB1_ENABLE 0x01000000
103 
104 #define KL0_SCC_B_INTF_ENABLE 0x00000001 /* (KL Only) */
105 #define KL0_SCC_A_INTF_ENABLE 0x00000002
106 #define KL0_SCC_SLOWPCLK 0x00000004
107 #define KL0_SCC_RESET 0x00000008
108 #define KL0_SCCA_ENABLE 0x00000010
109 #define KL0_SCCB_ENABLE 0x00000020
110 #define KL0_SCC_CELL_ENABLE 0x00000040
111 #define KL0_IRDA_HIGH_BAND 0x00000100 /* (KL Only) */
112 #define KL0_IRDA_SOURCE2_SEL 0x00000200 /* (KL Only) */
113 #define KL0_IRDA_SOURCE1_SEL 0x00000400 /* (KL Only) */
114 #define KL0_PG_USB0_PMI_ENABLE 0x00000400 /* (Pangea/Intrepid Only) */
115 #define KL0_IRDA_RESET 0x00000800 /* (KL Only) */
116 #define KL0_PG_USB0_REF_SUSPEND_SEL 0x00000800 /* (Pangea/Intrepid Only) */
117 #define KL0_IRDA_DEFAULT1 0x00001000 /* (KL Only) */
118 #define KL0_PG_USB0_REF_SUSPEND 0x00001000 /* (Pangea/Intrepid Only) */
119 #define KL0_IRDA_DEFAULT0 0x00002000 /* (KL Only) */
120 #define KL0_PG_USB0_PAD_SUSPEND 0x00002000 /* (Pangea/Intrepid Only) */
121 #define KL0_IRDA_FAST_CONNECT 0x00004000 /* (KL Only) */
122 #define KL0_PG_USB1_PMI_ENABLE 0x00004000 /* (Pangea/Intrepid Only) */
123 #define KL0_IRDA_ENABLE 0x00008000 /* (KL Only) */
124 #define KL0_PG_USB1_REF_SUSPEND_SEL 0x00008000 /* (Pangea/Intrepid Only) */
125 #define KL0_IRDA_CLK32_ENABLE 0x00010000 /* (KL Only) */
126 #define KL0_PG_USB1_REF_SUSPEND 0x00010000 /* (Pangea/Intrepid Only) */
127 #define KL0_IRDA_CLK19_ENABLE 0x00020000 /* (KL Only) */
128 #define KL0_PG_USB1_PAD_SUSPEND 0x00020000 /* (Pangea/Intrepid Only) */
129 #define KL0_USB0_PAD_SUSPEND0 0x00040000
130 #define KL0_USB0_PAD_SUSPEND1 0x00080000
131 #define KL0_USB0_CELL_ENABLE 0x00100000
132 #define KL0_USB1_PAD_SUSPEND0 0x00400000
133 #define KL0_USB1_PAD_SUSPEND1 0x00800000
134 #define KL0_USB1_CELL_ENABLE 0x01000000
135 #define KL0_USB_REF_SUSPEND 0x10000000 /* (KL Only) */
136 
137 #define KL0_SERIAL_ENABLE (KL0_SCC_B_INTF_ENABLE | \
138  KL0_SCC_SLOWPCLK | \
139  KL0_SCC_CELL_ENABLE | KL0_SCCA_ENABLE)
140 
141 #define KL1_USB2_PMI_ENABLE 0x00000001 /* Intrepid only */
142 #define KL1_AUDIO_SEL_22MCLK 0x00000002 /* KL/Pangea only */
143 #define KL1_USB2_REF_SUSPEND_SEL 0x00000002 /* Intrepid only */
144 #define KL1_USB2_REF_SUSPEND 0x00000004 /* Intrepid only */
145 #define KL1_AUDIO_CLK_ENABLE_BIT 0x00000008 /* KL/Pangea only */
146 #define KL1_USB2_PAD_SUSPEND_SEL 0x00000008 /* Intrepid only */
147 #define KL1_USB2_PAD_SUSPEND0 0x00000010 /* Intrepid only */
148 #define KL1_AUDIO_CLK_OUT_ENABLE 0x00000020 /* KL/Pangea only */
149 #define KL1_USB2_PAD_SUSPEND1 0x00000020 /* Intrepid only */
150 #define KL1_AUDIO_CELL_ENABLE 0x00000040 /* KL/Pangea only */
151 #define KL1_USB2_CELL_ENABLE 0x00000040 /* Intrepid only */
152 #define KL1_AUDIO_CHOOSE 0x00000080 /* KL/Pangea only */
153 #define KL1_I2S0_CHOOSE 0x00000200 /* KL Only */
154 #define KL1_I2S0_CELL_ENABLE 0x00000400
155 #define KL1_I2S0_CLK_ENABLE_BIT 0x00001000
156 #define KL1_I2S0_ENABLE 0x00002000
157 #define KL1_I2S1_CELL_ENABLE 0x00020000
158 #define KL1_I2S1_CLK_ENABLE_BIT 0x00080000
159 #define KL1_I2S1_ENABLE 0x00100000
160 #define KL1_EIDE0_ENABLE 0x00800000 /* KL/Intrepid Only */
161 #define KL1_EIDE0_RESET_N 0x01000000 /* KL/Intrepid Only */
162 #define KL1_EIDE1_ENABLE 0x04000000 /* KL Only */
163 #define KL1_EIDE1_RESET_N 0x08000000 /* KL Only */
164 #define KL1_UIDE_ENABLE 0x20000000 /* KL/Pangea Only */
165 #define KL1_UIDE_RESET_N 0x40000000 /* KL/Pangea Only */
166 
167 #define KL2_IOBUS_ENABLE 0x00000002
168 #define KL2_SLEEP_STATE_BIT 0x00000100 /* KL Only */
169 #define KL2_PG_STOP_ALL_CLOCKS 0x00000100 /* Pangea Only */
170 #define KL2_MPIC_ENABLE 0x00020000
171 #define KL2_CARDSLOT_RESET 0x00040000 /* Pangea/Intrepid Only */
172 #define KL2_ALT_DATA_OUT 0x02000000 /* KL Only ??? */
173 #define KL2_MEM_IS_BIG 0x04000000
174 #define KL2_CARDSEL_16 0x08000000
175 
176 #define KL3_SHUTDOWN_PLL_TOTAL 0x00000001 /* KL/Pangea only */
177 #define KL3_SHUTDOWN_PLLKW6 0x00000002 /* KL/Pangea only */
178 #define KL3_IT_SHUTDOWN_PLL3 0x00000002 /* Intrepid only */
179 #define KL3_SHUTDOWN_PLLKW4 0x00000004 /* KL/Pangea only */
180 #define KL3_IT_SHUTDOWN_PLL2 0x00000004 /* Intrepid only */
181 #define KL3_SHUTDOWN_PLLKW35 0x00000008 /* KL/Pangea only */
182 #define KL3_IT_SHUTDOWN_PLL1 0x00000008 /* Intrepid only */
183 #define KL3_SHUTDOWN_PLLKW12 0x00000010 /* KL Only */
184 #define KL3_IT_ENABLE_PLL3_SHUTDOWN 0x00000010 /* Intrepid only */
185 #define KL3_PLL_RESET 0x00000020 /* KL/Pangea only */
186 #define KL3_IT_ENABLE_PLL2_SHUTDOWN 0x00000020 /* Intrepid only */
187 #define KL3_IT_ENABLE_PLL1_SHUTDOWN 0x00000010 /* Intrepid only */
188 #define KL3_SHUTDOWN_PLL2X 0x00000080 /* KL Only */
189 #define KL3_CLK66_ENABLE 0x00000100 /* KL Only */
190 #define KL3_CLK49_ENABLE 0x00000200
191 #define KL3_CLK45_ENABLE 0x00000400
192 #define KL3_CLK31_ENABLE 0x00000800 /* KL/Pangea only */
193 #define KL3_TIMER_CLK18_ENABLE 0x00001000
194 #define KL3_I2S1_CLK18_ENABLE 0x00002000
195 #define KL3_I2S0_CLK18_ENABLE 0x00004000
196 #define KL3_VIA_CLK16_ENABLE 0x00008000 /* KL/Pangea only */
197 #define KL3_IT_VIA_CLK32_ENABLE 0x00008000 /* Intrepid only */
198 #define KL3_STOPPING33_ENABLED 0x00080000 /* KL Only */
199 #define KL3_PG_PLL_ENABLE_TEST 0x00080000 /* Pangea Only */
200 
201 /* Intrepid USB bus 2, port 0,1 */
202 #define KL3_IT_PORT_WAKEUP_ENABLE(p) (0x00080000 << ((p)<<3))
203 #define KL3_IT_PORT_RESUME_WAKE_EN(p) (0x00040000 << ((p)<<3))
204 #define KL3_IT_PORT_CONNECT_WAKE_EN(p) (0x00020000 << ((p)<<3))
205 #define KL3_IT_PORT_DISCONNECT_WAKE_EN(p) (0x00010000 << ((p)<<3))
206 #define KL3_IT_PORT_RESUME_STAT(p) (0x00300000 << ((p)<<3))
207 #define KL3_IT_PORT_CONNECT_STAT(p) (0x00200000 << ((p)<<3))
208 #define KL3_IT_PORT_DISCONNECT_STAT(p) (0x00100000 << ((p)<<3))
209 
210 /* Port 0,1 : bus 0, port 2,3 : bus 1 */
211 #define KL4_PORT_WAKEUP_ENABLE(p) (0x00000008 << ((p)<<3))
212 #define KL4_PORT_RESUME_WAKE_EN(p) (0x00000004 << ((p)<<3))
213 #define KL4_PORT_CONNECT_WAKE_EN(p) (0x00000002 << ((p)<<3))
214 #define KL4_PORT_DISCONNECT_WAKE_EN(p) (0x00000001 << ((p)<<3))
215 #define KL4_PORT_RESUME_STAT(p) (0x00000040 << ((p)<<3))
216 #define KL4_PORT_CONNECT_STAT(p) (0x00000020 << ((p)<<3))
217 #define KL4_PORT_DISCONNECT_STAT(p) (0x00000010 << ((p)<<3))
218 
219 /* Pangea and Intrepid only */
220 #define KL5_VIA_USE_CLK31 0000000001 /* Pangea Only */
221 #define KL5_SCC_USE_CLK31 0x00000002 /* Pangea Only */
222 #define KL5_PWM_CLK32_EN 0x00000004
223 #define KL5_CLK3_68_EN 0x00000010
224 #define KL5_CLK32_EN 0x00000020
225 
226 
227 /* K2 definitions */
228 #define K2_FCR0_USB0_SWRESET 0x00200000
229 #define K2_FCR0_USB1_SWRESET 0x02000000
230 #define K2_FCR0_RING_PME_DISABLE 0x08000000
231 
232 #define K2_FCR1_PCI1_BUS_RESET_N 0x00000010
233 #define K2_FCR1_PCI1_SLEEP_RESET_EN 0x00000020
234 #define K2_FCR1_I2S0_CELL_ENABLE 0x00000400
235 #define K2_FCR1_I2S0_RESET 0x00000800
236 #define K2_FCR1_I2S0_CLK_ENABLE_BIT 0x00001000
237 #define K2_FCR1_I2S0_ENABLE 0x00002000
238 #define K2_FCR1_PCI1_CLK_ENABLE 0x00004000
239 #define K2_FCR1_FW_CLK_ENABLE 0x00008000
240 #define K2_FCR1_FW_RESET_N 0x00010000
241 #define K2_FCR1_I2S1_CELL_ENABLE 0x00020000
242 #define K2_FCR1_I2S1_CLK_ENABLE_BIT 0x00080000
243 #define K2_FCR1_I2S1_ENABLE 0x00100000
244 #define K2_FCR1_GMAC_CLK_ENABLE 0x00400000
245 #define K2_FCR1_GMAC_POWER_DOWN 0x00800000
246 #define K2_FCR1_GMAC_RESET_N 0x01000000
247 #define K2_FCR1_SATA_CLK_ENABLE 0x02000000
248 #define K2_FCR1_SATA_POWER_DOWN 0x04000000
249 #define K2_FCR1_SATA_RESET_N 0x08000000
250 #define K2_FCR1_UATA_CLK_ENABLE 0x10000000
251 #define K2_FCR1_UATA_RESET_N 0x40000000
252 #define K2_FCR1_UATA_CHOOSE_CLK66 0x80000000
253 
254 /* Shasta definitions */
255 #define SH_FCR1_I2S2_CELL_ENABLE 0x00000010
256 #define SH_FCR1_I2S2_CLK_ENABLE_BIT 0x00000040
257 #define SH_FCR1_I2S2_ENABLE 0x00000080
258 #define SH_FCR3_I2S2_CLK18_ENABLE 0x00008000
259 
260 #endif /* __KERNEL__ */
261 #endif /* _ASM_POWERPC_KEYLARGO_H */
Generated on Thu Jan 10 2013 13:13:20 for Linux Kernel by   doxygen 1.8.2