Linux Kernel  3.7.1
 All Data Structures Namespaces Files Functions Variables Typedefs Enumerations Enumerator Macros Groups Pages
tuner-types.h
Go to the documentation of this file.
1 /*
2  * descriptions for simple tuners.
3  */
4 
5 #ifndef __TUNER_TYPES_H__
6 #define __TUNER_TYPES_H__
7 
8 enum param_type {
14 };
15 
16 struct tuner_range {
17  unsigned short limit;
18  unsigned char config;
19  unsigned char cb;
20 };
21 
22 struct tuner_params {
24 
25  /* Many Philips based tuners have a comment like this in their
26  * datasheet:
27  *
28  * For channel selection involving band switching, and to ensure
29  * smooth tuning to the desired channel without causing
30  * unnecessary charge pump action, it is recommended to consider
31  * the difference between wanted channel frequency and the
32  * current channel frequency. Unnecessary charge pump action
33  * will result in very low tuning voltage which may drive the
34  * oscillator to extreme conditions.
35  *
36  * Set cb_first_if_lower_freq to 1, if this check is
37  * required for this tuner.
38  *
39  * I tested this for PAL by first setting the TV frequency to
40  * 203 MHz and then switching to 96.6 MHz FM radio. The result was
41  * static unless the control byte was sent first.
42  */
43  unsigned int cb_first_if_lower_freq:1;
44  /* Set to 1 if this tuner uses a tda9887 */
45  unsigned int has_tda9887:1;
46  /* Many Philips tuners use tda9887 PORT1 to select the FM radio
47  sensitivity. If this setting is 1, then set PORT1 to 1 to
48  get proper FM reception. */
49  unsigned int port1_fm_high_sensitivity:1;
50  /* Some Philips tuners use tda9887 PORT2 to select the FM radio
51  sensitivity. If this setting is 1, then set PORT2 to 1 to
52  get proper FM reception. */
53  unsigned int port2_fm_high_sensitivity:1;
54  /* Some Philips tuners use tda9887 cGainNormal to select the FM radio
55  sensitivity. If this setting is 1, e register will use cGainNormal
56  instead of cGainLow. */
57  unsigned int fm_gain_normal:1;
58  /* Most tuners with a tda9887 use QSS mode. Some (cheaper) tuners
59  use Intercarrier mode. If this setting is 1, then the tuner
60  needs to be set to intercarrier mode. */
61  unsigned int intercarrier_mode:1;
62  /* This setting sets the default value for PORT1.
63  0 means inactive, 1 means active. Note: the actual bit
64  value written to the tda9887 is inverted. So a 0 here
65  means a 1 in the B6 bit. */
66  unsigned int port1_active:1;
67  /* This setting sets the default value for PORT2.
68  0 means inactive, 1 means active. Note: the actual bit
69  value written to the tda9887 is inverted. So a 0 here
70  means a 1 in the B7 bit. */
71  unsigned int port2_active:1;
72  /* Sometimes PORT1 is inverted when the SECAM-L' standard is selected.
73  Set this bit to 1 if this is needed. */
74  unsigned int port1_invert_for_secam_lc:1;
75  /* Sometimes PORT2 is inverted when the SECAM-L' standard is selected.
76  Set this bit to 1 if this is needed. */
77  unsigned int port2_invert_for_secam_lc:1;
78  /* Some cards require PORT1 to be 1 for mono Radio FM and 0 for stereo. */
79  unsigned int port1_set_for_fm_mono:1;
80  /* Select 18% (or according to datasheet 0%) L standard PLL gating,
81  vs the driver default of 36%. */
82  unsigned int default_pll_gating_18:1;
83  /* IF to use in radio mode. Tuners with a separate radio IF filter
84  seem to use 10.7, while those without use 33.3 for PAL/SECAM tuners
85  and 41.3 for NTSC tuners. 0 = 10.7, 1 = 33.3, 2 = 41.3 */
86  unsigned int radio_if:2;
87  /* Default tda9887 TOP value in dB for the low band. Default is 0.
88  Range: -16:+15 */
89  signed int default_top_low:5;
90  /* Default tda9887 TOP value in dB for the mid band. Default is 0.
91  Range: -16:+15 */
92  signed int default_top_mid:5;
93  /* Default tda9887 TOP value in dB for the high band. Default is 0.
94  Range: -16:+15 */
95  signed int default_top_high:5;
96  /* Default tda9887 TOP value in dB for SECAM-L/L' for the low band.
97  Default is 0. Several tuners require a different TOP value for
98  the SECAM-L/L' standards. Range: -16:+15 */
99  signed int default_top_secam_low:5;
100  /* Default tda9887 TOP value in dB for SECAM-L/L' for the mid band.
101  Default is 0. Several tuners require a different TOP value for
102  the SECAM-L/L' standards. Range: -16:+15 */
103  signed int default_top_secam_mid:5;
104  /* Default tda9887 TOP value in dB for SECAM-L/L' for the high band.
105  Default is 0. Several tuners require a different TOP value for
106  the SECAM-L/L' standards. Range: -16:+15 */
108 
110 
111  unsigned int count;
113 };
114 
115 struct tunertype {
116  char *name;
117  unsigned int count;
119 
123 
126 };
127 
128 extern struct tunertype tuners[];
129 extern unsigned const int tuner_count;
130 
131 #endif