Alignment and Distribution of Objects

This section describes the Allinea e Distribuisci dialog (Oggetto Allinea e Distribuisci... (Shift+Ctrl+A)) which allows the positioning of objects with respect to other objects or to the selection, drawing, or page. Two types of positioning are available: alignment where the centers or edges of objects are aligned to one another, and distributing where objects are distributed in some direction based on their centers or edges.

Align and Distribute dialog.
Allinea e Distribuisci dialog.

Align

The alignment of objects is with respect to an anchor. The anchor can be an object or be defined by the selection, drawing, or page; the choice of what is used is set in the pull-down menu Relative to. The object may be specified to be the first or last object selected. If multiple objects are selected at the same time, this is equivalent to the top or bottom object in z-order. Alternatively, the object can be specified to be the biggest or smallest item, where size is determined by the size of the quadro delimitatore, the width for vertical alignment and the height for horizontal alignment. The quadro delimitatore sides are used as the reference points for alignment except for text, where the Linea base is used.

The various alignment options are:

  • Horizontal:

    • Align right sides to left side of anchor.

    • Align right sides to right side of anchor.

    • Align horizontal centers to center of anchor.

    • Align left sides to left side of anchor.

    • Align left sides to right side of anchor.

    • Align baselines of text to anchor, horizontally.

  • Vertical:

    • Align top sides to bottom side of anchor.

    • Align top sides to top side of anchor.

    • Align vertical centers to center of anchor.

    • Align bottom sides to bottom side of anchor.

    • Align bottom sides to top side of anchor.

    • Align baselines of text to anchor, vertically.

Distribute: Uniform

The distribute part of the Allinea e Distribuisci dialog allows objects to be evenly spaced in the horizontal or vertical direction based on some criteria. Two options are included in this part of the dialog, which perhaps should be included separately: randomizing the center of objects and unclumping. They will be considered in the next section.

The distribution of objects is between the two objects at the extremes (i.e., the leftmost and rightmost objects for horizontal distribution). The definition of which is the leftmost and rightmost object is made using the objects' quadri delimitatori, and it may depend on the type of distribution selected. For example, if a distribution is based on the rightmost edge of the objects, then the objects rightmost edge will be used to determine which objects are at the extremes.

The various distribution options are:

  • Horizontal:

    • Distribute left sides evenly.

    • Distribute centers evenly.

    • Distribute right sides evenly.

    • Distribute with uniform gaps between objects.

    • Distribute baseline anchors evenly.

  • Vertical

    • Distribute left sides evenly.

    • Distribute centers evenly.

    • Distribute top sides evenly.

    • Distribute with uniform gaps between objects.

    • Distribute baseline anchors evenly.

Distribute: Non-Uniform

The distribute part of the Allinea e Distribuisci dialog has two options that modify the distribution of objects in a non-uniform way. Both affect the horizontal and vertical distributions at the same time.

The two options are:

  • Randomize the center of objects.

  • Unclump objects (i.e., move objects to more evenly space the edge-to-edge distances). Repeated application approaches the use of the Distribute with uniform gaps commands described above.

Distribute: Remove Overlaps

Another section of the Allinea e Distribuisci dialog allows one to move objects just enough that they don't overlap. Two entry boxes, one for the horizontal direction and the other for the vertical direction, allow the addition of a minimum space between adjacent objects.

Rows and Columns

Used to be called Grid Arrange.

The Righe e Colonne dialog (Oggetto Righe e Colonne... ) can be used to arrange an arbitrary number of objects into a two-dimensional grid.

Rows and Columns dialog.
Righe e Colonne dialog.

To use the dialog, first select all the objects you wish to arrange into a grid. The dialog will default to a one-dimensional array. You can use the Row and Column entry boxes to change the number of rows and columns. If you use the up/down arrows to change the number of rows, the number of columns will change to give you the minimum number required to include all the objects in the selection. A similar change to the number of rows will happen if you change the number of columns. The maximum number of rows or columns is 100.

The algorithm for determining the order the objects are placed in the array attempts to preserve any existing rows. For this algorithm, the quadro delimitatore of each object is used. Technically, the objects are first sorted by their vertical positions. Then objects that overlap vertically are sorted by their horizontal positions. Finally, the objects are placed from left to right and from top to bottom in the array. The algorithm works pretty well but cannot handle all situations since determining what objects are in a row is objective. (If in the vertical direction A overlaps B and B overlaps C but A does not overlap C, are A and C in the same row?)

Grid align 1.
Twelve object before (left) and after (right) aligning with a 3 by 4 grid.

For placing objects, the grid is divided into cells. First, the cell size and placement is determined and then the objects are positioned inside the cells, one object to one cell.

Cells are given the height of the tallest object if the Equal height box is checked; otherwise, they are given the height of the tallest object in their row. A similar policy is followed for width.

Grid align 2.
Alignment with the Equal height box checked (left) and unchecked (right). Note how the height of the '8' has been used for all rows on the left and just its own row on the right.

If the Fit into selection option is selected, the rows and columns of cells are evenly spaced with the edge rows and columns flush against the bounding box of the selection. If the Set spacing option is selected, the rows and columns are separated by the amount entered in the Row spacing and Column spacing entry boxes. The spacing can be negative.

Once the cell positions have been determined, the objects are placed inside the cell according to the selected Align options (top, middle, bottom; left, center, right).

Grid align 3.
Grid alignment with alignment to top (left), center (middle), and bottom (right) of cell.

Note that the quadro delimitatore of all the objects after alignment may not be the same as the quadro delimitatore of the selection prior to alignment even though the Fit to selection option has been chosen. This is because the selection quadro delimitatore has been used to place the cells. The objects within the cells may not touch the cell walls. (There also appears sometimes to be a gratuitous shift: Bug?)