Previous
Logging In to a Zone
Use the zlogin command to log in from the global zone to any zone that is running or in the ready state. See the zlogin(1) man page for more information.
You can log in to a zone in various ways, as described in the following procedures. You can also log in remotely, as described in Remote Login.
How to Log In to the Zone Console
You must be the global administrator in the global zone to perform this procedure.
Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see "Using the Solaris Management Tools With RBAC (Task Map)" in System Administration Guide: Basic Administration.
Use the zlogin command with the -C option and the name of the zone, for example, my-zone.
global# zlogin -C my-zone
Note - If you start the zlogin session immediately after issuing the zoneadm boot command, boot messages from the zone will display:
SunOS Release 5.10 Version Generic 64-bit Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. starting rpc services: rpcbind done. syslog service starting. The system is ready.
When the zone console displays, log in as root, press Return, and type the root password when prompted.
my-zone console login: root Password:
How to Use Interactive Mode to Access a Zone
In interactive mode, a new pseudo-terminal is allocated for use inside the zone.
You must be the global administrator in the global zone to perform this procedure.
Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see "Using the Solaris Management Tools With RBAC (Task Map)" in System Administration Guide: Basic Administration.
From the global zone, log in to the zone, for example, my-zone.
global# zlogin my-zone
Information similar to the following will display:
[Connected to zone 'my-zone' pts/2] Last login: Wed Jul 3 16:25:00 on console Sun Microsystems Inc. SunOS 5.10 Generic July 2004
Type exit to close the connection.
You will see a message similar to the following:
[Connection to zone 'my-zone' pts/2 closed]
How to Use Non-Interactive Mode to Access
a Zone
Non-interactive mode is enabled when the user supplies a command to be run inside the zone. Non-interactive mode does not allocate a new pseudo-terminal.
Note that the command or any files that the command acts upon cannot reside on NFS.
You must be the global administrator in the global zone to perform this procedure.
Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see "Using the Solaris Management Tools With RBAC (Task Map)" in System Administration Guide: Basic Administration.
From the global zone, log in to the my-zone zone and supply a command name.
The command zonename is used here.
global# zlogin my-zone zonename
You will see the following output:
my-zone
How to Exit a Non-Global Zone
To disconnect from a non-global zone, use the tilde (~) character and a period:
zonename# ~.
Your screen will look similar to this:
[Connection to zone 'my-zone' pts/6 closed]
You can also type exit to exit the zone.
See Also
For more information about zlogin command options, see the zlogin(1) man page.
How to Use Failsafe Mode to Enter a Zone
When a connection to the zone is denied, the zlogin command can be used with the -S option to enter a minimal environment in the zone.
You must be the global administrator in the global zone to perform this procedure.
Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see "Using the Solaris Management Tools With RBAC (Task Map)" in System Administration Guide: Basic Administration.
From the global zone, use the zlogin command with the -S option to access the zone, for example, my-zone.
global# zlogin -S my-zone
How to Use zlogin to
Shut Down a Zone
Note - Running init 0 in the global zone to cleanly shut down a Solaris system also runs init 0 in each of the non-global zones on the system. Note that init 0 does not warn local and remote users to log off before the system is taken down.
Use this procedure to cleanly shut down a zone. To halt a zone without running shutdown scripts, see How to Halt a Zone.
You must be the global administrator in the global zone to perform this procedure.
Become superuser, or assume the Primary Administrator role.
To create the role and assign the role to a user, see "Using the Solaris Management Tools With RBAC (Task Map)" in System Administration Guide: Basic Administration.
Log in to the zone to be shut down, for example, my-zone, and specify shutdown as the name of the utility and init 0 as the state.
global# zlogin my-zone shutdown -i 0
Your site might have its own shutdown script, tailored for your specific environment.
More Information
Using shutdown in Non-Interactive
Mode
You cannot use the shutdown command in non-interactive mode to place the zone in single-user state at this time. See 6214427 for more information.
You can use an interactive login as described in How to Use Interactive Mode to Access a Zone.