How to Replace a Slice in a Submirror
Read Overview of Replacing and Enabling Components in RAID-1 and RAID-5 Volumes and Creating and Maintaining RAID-1 Volumes.
Make sure that you have root privilege and that you have a current backup of all data.
Use the metastat command to view the status of the RAID-1 volume and associated submirrors.
# metastat mirror-name
Use one of the following methods to replace a slice in a submirror.
From the Enhanced Storage tool within the Solaris Management Console, open the Volumes node. Choose the mirror. Then, choose Action⇒Properties and click the Submirror tab. Follow the onscreen instructions. For more information, see the online help.
Use the following form of the metareplace command to replace a slice in a submirror:
# metareplace mirror-name component-name
mirror-name is the name of the
volume to create.
component-name specifies the name
of the component to replace.
mirror-name
Specifies the name of the volume to create
component-name
Specifies the name of the component to replace
See the following examples and the metainit ( 1M ) man page for more information.
Example 11.19. Replacing a Failed Slice in a Mirror
The following example illustrates how to replace a failed slice when the system is not configured to use hot spare pools for the automatic replacement of failed disks. See Chapter 16, Hot Spare Pools (Overview) for more information about using hot spare pools.
#metastat d6d6: Mirror Submirror 0: d16 State: Okay Submirror 1: d26 State: Needs maintenance ... d26: Submirror of d6 State: Needs maintenance Invoke: metareplace d6 c0t2d0s2 <new device> ... #metareplace d6 c0t2d0s2 c0t2d2s2d6: device c0t2d0s2 is replaced with c0t2d2s2
The metastat command confirms that mirror d6 has a submirror, d26, with a slice in the “Needs
maintenance” state. The metareplace command replaces
the slice as specified in the “Invoke” line of the metastat output
with another available slice on the system. The system confirms that the slice
is replaced, and starts resynchronizing the submirror.
How to Replace a Submirror
Read Overview of Replacing and Enabling Components in RAID-1 and RAID-5 Volumes and Creating and Maintaining RAID-1 Volumes.
Make sure that you have root privilege and that you have a current backup of all data.
Use the metastat command to view the status of the RAID-1 volume and associated submirrors.
# metastat mirror-name
Use one of the following methods to replace a submirror.
From the Enhanced Storage tool within the Solaris Management Console, open the Volumes node. Choose the mirror. Then, choose Action⇒Properties and click the Submirror tab. Follow the onscreen instructions. For more information, see the online help.
Use the metadetach, metaclear, metatinit, and metattach commands to replace an entire submirror.
Use the metadetach command to the failed submirror from the mirror.
# metadetach -f mirror-name submirror
f
Forces the detach to occur
mirror-name
Specifies the name of the mirror
submirror
Specifies the submirror to detach
Use the metaclear command to delete the submirror.
# metaclear -f submirror
f
Forces the deletion of the submirror to occur
submirror
Specifies the submirror to delete
Use the metainit command to create a new submirror.
# metainit volume-name number-of-stripes components-per-stripe component-name
volume-name
Specifies the name of the volume to create. For information on naming volumes, see Volume Names.
number-of-stripes
Specifies the number of stripes to create.
components-per-stripe
Specifies the number of components each stripe should have.
component-names
Specifies the names of the components that are used. This
example uses the root slice, c0t0d0s0.
Use the metattach command to attach the new submirror.
# metattach mirror submirror
Example 11.20. Replacing a Submirror in a Mirror
The following example illustrates how to replace a submirror in an active mirror.
#metastat d20d20: Mirror Submirror 0: d21 State: Okay Submirror 1: d22 State: Needs maintenance ... #metadetach -f d20 d22d20: submirror d22 is detached #metaclear -f d22d22: Concat/Stripe is cleared #metainit d22 2 1 c1t0d0s2 1 c1t0d1s2d22: Concat/Stripe is setup #metattach d20 d22d20: components are attached
In this example, the metastat command confirms
that the two-way mirror, d20, has a submirror, d22, in the “Needs maintenance” state. In this case, the
entire submirror needs to be cleared and recreated. The metadetach command
detaches the failed submirror from the mirror by using the
f option,
which forces the detachment to occur. The metaclear command
clears the submirror. The metainit command recreates submirror, d22, with new slices. Finally, the metattach command
attaches the rebuilt submirror. A mirror resynchronization begins automatically.
The specific configuration of the new volume, d22,
depends on the component you are replacing. A concatenation, as shown here,
can sufficiently replace a concatenation. However, a concatenation would not
be an ideal replacement for a stripe because it could impact performance.
You temporarily lose the capability for data redundancy while the mirror is a one-way mirror.