Product SiteDocumentation Site

6.2. Configuring a DHCP Server

The dhcp package contains an ISC DHCP server. First, install the package as the superuser:
~]# yum install dhcp
Installing the dhcp package creates a file, /etc/dhcp/dhcpd.conf, which is merely an empty configuration file:
~]# cat /etc/dhcp/dhcpd.conf
#
# DHCP Server Configuration file.
#   see /usr/share/doc/dhcp*/dhcpd.conf.sample
The sample configuration file can be found at /usr/share/doc/dhcp-<version>/dhcpd.conf.sample. You should use this file to help you configure /etc/dhcp/dhcpd.conf, which is explained in detail below.
DHCP also uses the file /var/lib/dhcpd/dhcpd.leases to store the client lease database. Refer to Section 6.2.2, “Lease Database” for more information.

6.2.1. Configuration File

The first step in configuring a DHCP server is to create the configuration file that stores the network information for the clients. Use this file to declare options and global options for client systems.
The configuration file can contain extra tabs or blank lines for easier formatting. Keywords are case-insensitive and lines beginning with a hash sign (#) are considered comments.
There are two types of statements in the configuration file:
  • Parameters — State how to perform a task, whether to perform a task, or what network configuration options to send to the client.
  • Declarations — Describe the topology of the network, describe the clients, provide addresses for the clients, or apply a group of parameters to a group of declarations.
The parameters that start with the keyword option are reffered to as options. These options control DHCP options; whereas, parameters configure values that are not optional or control how the DHCP server behaves.
Parameters (including options) declared before a section enclosed in curly brackets ({ }) are considered global parameters. Global parameters apply to all the sections below it.

Important

If the configuration file is changed, the changes do not take effect until the DHCP daemon is restarted with the command service dhcpd restart.

Tip

Instead of changing a DHCP configuration file and restarting the service each time, using the omshell command provides an interactive way to connect to, query, and change the configuration of a DHCP server. By using omshell, all changes can be made while the server is running. For more information on omshell, refer to the omshell man page.
In Example 6.1, “Subnet Declaration”, the routers, subnet-mask, domain-search, domain-name-servers, and time-offset options are used for any host statements declared below it.
Additionally, a subnet can be declared, a subnet declaration must be included for every subnet in the network. If it is not, the DHCP server fails to start.
In this example, there are global options for every DHCP client in the subnet and a range declared. Clients are assigned an IP address within the range.
Example 6.1. Subnet Declaration
subnet 192.168.1.0 netmask 255.255.255.0 {
        option routers                  192.168.1.254;
        option subnet-mask              255.255.255.0;
        option domain-search              "example.com";
        option domain-name-servers       192.168.1.1;
        option time-offset              -18000;     # Eastern Standard Time
	range 192.168.1.10 192.168.1.100;
}

To configure a DHCP server that leases a dynamic IP address to a system within a subnet, modify Example 6.2, “Range Parameter” with your values. It declares a default lease time, maximum lease time, and network configuration values for the clients. This example assigns IP addresses in the range 192.168.1.10 and 192.168.1.100 to client systems.
Example 6.2. Range Parameter
default-lease-time 600;
max-lease-time 7200;
option subnet-mask 255.255.255.0;
option broadcast-address 192.168.1.255;
option routers 192.168.1.254;
option domain-name-servers 192.168.1.1, 192.168.1.2;
option domain-search "example.com";
subnet 192.168.1.0 netmask 255.255.255.0 {
   range 192.168.1.10 192.168.1.100;
}

To assign an IP address to a client based on the MAC address of the network interface card, use the hardware ethernet parameter within a host declaration. As demonstrated in Example 6.3, “Static IP Address using DHCP”, the host apex declaration specifies that the network interface card with the MAC address 00:A0:78:8E:9E:AA always receives the IP address 192.168.1.4.
Note that the optional parameter host-name can also be used to assign a host name to the client.
Example 6.3. Static IP Address using DHCP
host apex {
   option host-name "apex.example.com";
   hardware ethernet 00:A0:78:8E:9E:AA;
   fixed-address 192.168.1.4;
}

All subnets that share the same physical network should be declared within a shared-network declaration as shown in Example 6.4, “Shared-network Declaration”. Parameters within the shared-network, but outside the enclosed subnet declarations, are considered to be global parameters. The name of the shared-network must be a descriptive title for the network, such as using the title 'test-lab' to describe all the subnets in a test lab environment.
Example 6.4. Shared-network Declaration
shared-network name {
    option domain-search              "test.redhat.com";
    option domain-name-servers      ns1.redhat.com, ns2.redhat.com;
    option routers                  192.168.0.254;
    more parameters for EXAMPLE shared-network
    subnet 192.168.1.0 netmask 255.255.252.0 {
        parameters for subnet
        range 192.168.1.1 192.168.1.254;
    }
    subnet 192.168.2.0 netmask 255.255.252.0 {
        parameters for subnet
        range 192.168.2.1 192.168.2.254;
    }
}

As demonstrated in Example 6.5, “Group Declaration”, the group declaration is used to apply global parameters to a group of declarations. For example, shared networks, subnets, and hosts can be grouped.
Example 6.5. Group Declaration
group {
   option routers                  192.168.1.254;
   option subnet-mask              255.255.255.0;
   option domain-search              "example.com";
   option domain-name-servers       192.168.1.1;
   option time-offset              -18000;     # Eastern Standard Time
   host apex {
      option host-name "apex.example.com";
      hardware ethernet 00:A0:78:8E:9E:AA;
      fixed-address 192.168.1.4;
   }
   host raleigh {
      option host-name "raleigh.example.com";
      hardware ethernet 00:A1:DD:74:C3:F2;
      fixed-address 192.168.1.6;
   }
}

Tip

The sample configuration file provided can be used as a starting point and custom configuration options can be added to it. To copy it to the proper location, use the following command:
cp /usr/share/doc/dhcp-<version-number>/dhcpd.conf.sample /etc/dhcp/dhcpd.conf
... where <version-number> is the DHCP version number.
For a complete list of option statements and what they do, refer to the dhcp-options man page.