Preparing Files for USB Memory Stick Booting

To prepare the USB stick, you will need a system where GNU/Linux is already running and where USB is supported. You should ensure that the usb-storage kernel module is loaded (modprobe usb-storage) and try to find out which SCSI device the USB stick has been mapped to (in this example /dev/sda is used). To write to your stick, you may have to turn off its write protection switch.

Note that the USB stick should be at least 8 MB in size. If you follow the section called “Copying the files — the flexible way” and want to include an Ubuntu ISO image on the stick, you will need enough space for the ISO as well.

Copying the files — the easy way

There is an all-in-one file netboot/boot.img.gz which contains all the installer files (including the kernel) as well as SYSLINUX and its configuration file. You only have to extract it directly to a partition on your USB stick:

# zcat boot.img.gz > /dev/sda1

[Warning]

Using this method will destroy anything already on the device. Make sure that you use the correct device name for your USB stick.

Copying the files — the flexible way

If you like more flexibility or just want to know what's going on, you should use the following method to put the files on your stick.

USB stick partitioning on Intel x86

We will show how to setup the memory stick to use the first partition, instead of the entire device.

[Note]

Since most USB sticks come pre-configured with a single FAT16 partition, you probably won't have to repartition or reformat the stick. If you have to do that anyway, use cfdisk or any other partitioning tool to create a FAT16 partition, and then create the filesystem using:

# mkdosfs /dev/sda1

Take care that you use the correct device name for your USB stick. The mkdosfs command is contained in the dosfstools Ubuntu package.

In order to start the kernel after booting from the USB stick, we will put a boot loader on the stick. Although any boot loader (e.g. LILO) should work, it's convenient to use SYSLINUX, since it uses a FAT16 partition and can be reconfigured by just editing a text file. Any operating system which supports the FAT file system can be used to make changes to the configuration of the boot loader.

To put SYSLINUX on the FAT16 partition on your USB stick, install the syslinux and mtools packages on your system, and do:

# syslinux /dev/sda1

Again, take care that you use the correct device name. The partition must not be mounted when starting SYSLINUX. This procedure writes a boot sector to the partition and creates the file ldlinux.sys which contains the boot loader code.

Mount the partition (mount /dev/sda1 /mnt) and copy the following files from the Ubuntu archives to the stick:

  • vmlinuz (kernel binary)

  • initrd.gz (initial ramdisk image)

  • syslinux.cfg (SYSLINUX configuration file)

  • Optional kernel modules

If you want to rename the files, please note that SYSLINUX can only process DOS (8.3) file names.

The syslinux.cfg configuration file should contain the following two lines:

default vmlinuz
append initrd=initrd.gz

Adding an ISO image

The installer will look for an Ubuntu ISO image on the stick as its source for additional data needed for the installation. So your next step is to copy an Ubuntu ISO image onto your stick (be sure to select one that fits). The file name of the image must end in .iso.

If you want to install over the network, without using an ISO image, you will of course skip the previous step. Moreover you will have to use the initial ramdisk from the netboot directory instead of the one from hd-media, because hd-media/initrd.gz does not have network support.

When you are done, unmount the USB memory stick (umount /mnt) and activate its write protection switch.

Booting the USB stick

[Warning]

If your system refuses to boot from the memory stick, the stick may contain an invalid master boot record (MBR). To fix this, use the install-mbr command from the package mbr:

# install-mbr /dev/sda