6.4. Building display filter expressions

Wireshark provides a simple but powerful display filter language that allows you to build quite complex filter expressions. You can compare values in packets as well as combine expressions into more specific expressions. The following sections provide more information on doing this.

[Tip]Tip!

You will find a lot of Display Filter examples at the Wireshark Wiki Display Filter page at http://wiki.wireshark.org/DisplayFilters.

6.4.1. Display filter fields

Every field in the packet details pane can be used as a filter string, this will result in showing only the packets where this field exists. For example: the filter string: tcp will show all packets containing the tcp protocol.

There is a complete list of all filter fields available through the menu item "Help/Supported Protocols" in the page "Display Filter Fields" of the Supported Protocols dialog.

XXX - add some more info here and a link to the statusbar info.

6.4.2. Comparing values

You can build display filters that compare values using a number of different comparison operators. They are shown in Table 6.3, “Display Filter comparison operators”.

[Tip]Tip!

You can use English and C-like terms in the same way, they can even be mixed in a filter string!

Table 6.3. Display Filter comparison operators

EnglishC-likeDescription and example
eq
==

Equal

ip.src==10.0.0.5

ne
!=

Not equal

ip.src!=10.0.0.5

gt
>

Greater than

frame.len > 10

lt
<

Less than

frame.len < 128

ge
>=

Greater than or equal to

frame.len ge 0x100

le
<=

Less than or equal to

frame.len <= 0x20


In addition, all protocol fields are typed. Table 6.4, “Display Filter Field Types” provides a list of the types and example of how to express them.

Table 6.4. Display Filter Field Types

TypeExample
Unsigned integer (8-bit, 16-bit, 24-bit, 32-bit)

You can express integers in decimal, octal, or hexadecimal. The following display filters are equivalent:

ip.len le 1500
ip.len le 02734
ip.len le 0x436
			

Signed integer (8-bit, 16-bit, 24-bit, 32-bit)  
Boolean

A boolean field is present in the protocol decode only if its value is true. For example, tcp.flags.syn is present, and thus true, only if the SYN flag is present in a TCP segment header.

Thus the filter expression tcp.flags.syn will select only those packets for which this flag exists, that is, TCP segments where the segment header contains the SYN flag. Similarly, to find source-routed token ring packets, use a filter expression of tr.sr.

Ethernet address (6 bytes)

Separators can be a colon (:), dot (.) or dash (-) and can have one or two bytes between separators:

eth.dst == ff:ff:ff:ff:ff:ff
eth.dst == ff-ff-ff-ff-ff-ff
eth.dst == ffff.ffff.ffff
IPv4 address

ip.addr == 192.168.0.1

Classless InterDomain Routing (CIDR) notation can be used to test if an IPv4 address is in a certain subnet. For example, this display filter will find all packets in the 129.111 Class-B network:

ip.addr == 129.111.0.0/16

IPv6 addressipv6.addr == ::1
IPX addressipx.addr == 00000000.ffffffffffff
String (text)http.request.uri == "http://www.wireshark.org/"


6.4.3. Combining expressions

You can combine filter expressions in Wireshark using the logical operators shown in Table 6.5, “Display Filter Logical Operations”

Table 6.5. Display Filter Logical Operations

EnglishC-likeDescription and example
and&&

Logical AND

ip.src==10.0.0.5 and tcp.flags.fin

or||

Logical OR

ip.scr==10.0.0.5 or ip.src==192.1.1.1

xor^^

Logical XOR

tr.dst[0:3] == 0.6.29 xor tr.src[0:3] == 0.6.29

not!

Logical NOT

not llc

[...] 

Substring Operator

Wireshark allows you to select subsequences of a sequence in rather elaborate ways. After a label you can place a pair of brackets [] containing a comma separated list of range specifiers.

eth.src[0:3] == 00:00:83

The example above uses the n:m format to specify a single range. In this case n is the beginning offset and m is the length of the range being specified.

eth.src[1-2] == 00:83
		    

The example above uses the n-m format to specify a single range. In this case n is the beginning offset and m is the ending offset.

eth.src[:4] == 00:00:83:00

The example above uses the :m format, which takes everything from the beginning of a sequence to offset m. It is equivalent to 0:m

eth.src[4:] == 20:20

The example above uses the n: format, which takes everything from offset n to the end of the sequence.

eth.src[2] == 83

The example above uses the n format to specify a single range. In this case the element in the sequence at offset n is selected. This is equivalent to n:1.

eth.src[0:3,1-2,:4,4:,2] == 
00:00:83:00:83:00:00:83:00:20:20:83

Wireshark allows you to string together single ranges in a comma separated list to form compound ranges as shown above.


6.4.4. A common mistake

[Warning]Warning!

Using the != operator on combined expressions like: eth.addr, ip.addr, tcp.port, udp.port and alike will probably not work as expected!

Often people use a filter string to display something like ip.addr == 1.2.3.4 which will display all packets containing the IP address 1.2.3.4.

Then they use ip.addr != 1.2.3.4 to see all packets not containing the IP address 1.2.3.4 in it. Unfortunately, this does not do the expected.

Instead, that expression will even be true for packets where either source or destination IP address equals 1.2.3.4. The reason for this, is that the expression ip.addr != 1.2.3.4 must be read as "the packet contains a field named ip.addr with a value different from 1.2.3.4". As an IP datagram contains both a source and a destination address, the expression will evaluate to true whenever at least one of the two addresses differs from 1.2.3.4.

If you want to filter out all packets containing IP datagrams to or from IP address 1.2.3.4, then the correct filter is !(ip.addr == 1.2.3.4) as it reads "show me all the packets for which it is not true that a field named ip.addr exists with a value of 1.2.3.4", or in other words, "filter out all packets for which there are no occurrences of a field named ip.addr with the value 1.2.3.4".