serial_reg.h

Go to the documentation of this file.

/*
 * include/linux/serial_reg.h
 *
 * Copyright (C) 1992, 1994 by Theodore Ts'o.
 * 
 * Redistribution of this file is permitted under the terms of the GNU 
 * Public License (GPL)
 * 
 * These are the UART port assignments, expressed as offsets from the base
 * register.  These assignments should hold for any serial port based on
 * a 8250, 16450, or 16550(A).
 */

#ifndef _LINUX_SERIAL_REG_H
#define _LINUX_SERIAL_REG_H

/*
 * DLAB=0
 */
#define UART_RX     0   /* In:  Receive buffer */
#define UART_TX     0   /* Out: Transmit buffer */

#define UART_IER    1   /* Out: Interrupt Enable Register */
#define UART_IER_MSI        0x08 /* Enable Modem status interrupt */
#define UART_IER_RLSI       0x04 /* Enable receiver line status interrupt */
#define UART_IER_THRI       0x02 /* Enable Transmitter holding register int. */
#define UART_IER_RDI        0x01 /* Enable receiver data interrupt */
/*
 * Sleep mode for ST16650 and TI16750.  For the ST16650, EFR[4]=1
 */
#define UART_IERX_SLEEP     0x10 /* Enable sleep mode */

#define UART_IIR    2   /* In:  Interrupt ID Register */
#define UART_IIR_NO_INT     0x01 /* No interrupts pending */
#define UART_IIR_ID     0x06 /* Mask for the interrupt ID */
#define UART_IIR_MSI        0x00 /* Modem status interrupt */
#define UART_IIR_THRI       0x02 /* Transmitter holding register empty */
#define UART_IIR_RDI        0x04 /* Receiver data interrupt */
#define UART_IIR_RLSI       0x06 /* Receiver line status interrupt */

#define UART_IIR_BUSY       0x07 /* DesignWare APB Busy Detect */

#define UART_IIR_RX_TIMEOUT 0x0c /* OMAP RX Timeout interrupt */
#define UART_IIR_XOFF       0x10 /* OMAP XOFF/Special Character */
#define UART_IIR_CTS_RTS_DSR    0x20 /* OMAP CTS/RTS/DSR Change */

#define UART_FCR    2   /* Out: FIFO Control Register */
#define UART_FCR_ENABLE_FIFO    0x01 /* Enable the FIFO */
#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
/*
 * Note: The FIFO trigger levels are chip specific:
 *  RX:76 = 00  01  10  11  TX:54 = 00  01  10  11
 * PC16550D:     1   4   8  14      xx  xx  xx  xx
 * TI16C550A:    1   4   8  14          xx  xx  xx  xx
 * TI16C550C:    1   4   8  14          xx  xx  xx  xx
 * ST16C550:     1   4   8  14      xx  xx  xx  xx
 * ST16C650:     8  16  24  28      16   8  24  30  PORT_16650V2
 * NS16C552:     1   4   8  14      xx  xx  xx  xx
 * ST16C654:     8  16  56  60       8  16  32  56  PORT_16654
 * TI16C750:     1  16  32  56      xx  xx  xx  xx  PORT_16750
 * TI16C752:     8  16  56  60       8  16  32  56
 * Tegra:    1   4   8  14      16   8   4   1  PORT_TEGRA
 */
#define UART_FCR_R_TRIG_00  0x00
#define UART_FCR_R_TRIG_01  0x40
#define UART_FCR_R_TRIG_10  0x80
#define UART_FCR_R_TRIG_11  0xc0
#define UART_FCR_T_TRIG_00  0x00
#define UART_FCR_T_TRIG_01  0x10
#define UART_FCR_T_TRIG_10  0x20
#define UART_FCR_T_TRIG_11  0x30

#define UART_FCR_TRIGGER_MASK   0xC0 /* Mask for the FIFO trigger range */
#define UART_FCR_TRIGGER_1  0x00 /* Mask for trigger set at 1 */
#define UART_FCR_TRIGGER_4  0x40 /* Mask for trigger set at 4 */
#define UART_FCR_TRIGGER_8  0x80 /* Mask for trigger set at 8 */
#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
/* 16650 definitions */
#define UART_FCR6_R_TRIGGER_8   0x00 /* Mask for receive trigger set at 1 */
#define UART_FCR6_R_TRIGGER_16  0x40 /* Mask for receive trigger set at 4 */
#define UART_FCR6_R_TRIGGER_24  0x80 /* Mask for receive trigger set at 8 */
#define UART_FCR6_R_TRIGGER_28  0xC0 /* Mask for receive trigger set at 14 */
#define UART_FCR6_T_TRIGGER_16  0x00 /* Mask for transmit trigger set at 16 */
#define UART_FCR6_T_TRIGGER_8   0x10 /* Mask for transmit trigger set at 8 */
#define UART_FCR6_T_TRIGGER_24  0x20 /* Mask for transmit trigger set at 24 */
#define UART_FCR6_T_TRIGGER_30  0x30 /* Mask for transmit trigger set at 30 */
#define UART_FCR7_64BYTE    0x20 /* Go into 64 byte mode (TI16C750) */

#define UART_LCR    3   /* Out: Line Control Register */
/*
 * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting 
 * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
 */
#define UART_LCR_DLAB       0x80 /* Divisor latch access bit */
#define UART_LCR_SBC        0x40 /* Set break control */
#define UART_LCR_SPAR       0x20 /* Stick parity (?) */
#define UART_LCR_EPAR       0x10 /* Even parity select */
#define UART_LCR_PARITY     0x08 /* Parity Enable */
#define UART_LCR_STOP       0x04 /* Stop bits: 0=1 bit, 1=2 bits */
#define UART_LCR_WLEN5      0x00 /* Wordlength: 5 bits */
#define UART_LCR_WLEN6      0x01 /* Wordlength: 6 bits */
#define UART_LCR_WLEN7      0x02 /* Wordlength: 7 bits */
#define UART_LCR_WLEN8      0x03 /* Wordlength: 8 bits */

/*
 * Access to some registers depends on register access / configuration
 * mode.
 */
#define UART_LCR_CONF_MODE_A    UART_LCR_DLAB   /* Configutation mode A */
#define UART_LCR_CONF_MODE_B    0xBF        /* Configutation mode B */

#define UART_MCR    4   /* Out: Modem Control Register */
#define UART_MCR_CLKSEL     0x80 /* Divide clock by 4 (TI16C752, EFR[4]=1) */
#define UART_MCR_TCRTLR     0x40 /* Access TCR/TLR (TI16C752, EFR[4]=1) */
#define UART_MCR_XONANY     0x20 /* Enable Xon Any (TI16C752, EFR[4]=1) */
#define UART_MCR_AFE        0x20 /* Enable auto-RTS/CTS (TI16C550C/TI16C750) */
#define UART_MCR_LOOP       0x10 /* Enable loopback test mode */
#define UART_MCR_OUT2       0x08 /* Out2 complement */
#define UART_MCR_OUT1       0x04 /* Out1 complement */
#define UART_MCR_RTS        0x02 /* RTS complement */
#define UART_MCR_DTR        0x01 /* DTR complement */

#define UART_LSR    5   /* In:  Line Status Register */
#define UART_LSR_FIFOE      0x80 /* Fifo error */
#define UART_LSR_TEMT       0x40 /* Transmitter empty */
#define UART_LSR_THRE       0x20 /* Transmit-hold-register empty */
#define UART_LSR_BI     0x10 /* Break interrupt indicator */
#define UART_LSR_FE     0x08 /* Frame error indicator */
#define UART_LSR_PE     0x04 /* Parity error indicator */
#define UART_LSR_OE     0x02 /* Overrun error indicator */
#define UART_LSR_DR     0x01 /* Receiver data ready */
#define UART_LSR_BRK_ERROR_BITS 0x1E /* BI, FE, PE, OE bits */

#define UART_MSR    6   /* In:  Modem Status Register */
#define UART_MSR_DCD        0x80 /* Data Carrier Detect */
#define UART_MSR_RI     0x40 /* Ring Indicator */
#define UART_MSR_DSR        0x20 /* Data Set Ready */
#define UART_MSR_CTS        0x10 /* Clear to Send */
#define UART_MSR_DDCD       0x08 /* Delta DCD */
#define UART_MSR_TERI       0x04 /* Trailing edge ring indicator */
#define UART_MSR_DDSR       0x02 /* Delta DSR */
#define UART_MSR_DCTS       0x01 /* Delta CTS */
#define UART_MSR_ANY_DELTA  0x0F /* Any of the delta bits! */

#define UART_SCR    7   /* I/O: Scratch Register */

/*
 * DLAB=1
 */
#define UART_DLL    0   /* Out: Divisor Latch Low */
#define UART_DLM    1   /* Out: Divisor Latch High */

/*
 * LCR=0xBF (or DLAB=1 for 16C660)
 */
#define UART_EFR    2   /* I/O: Extended Features Register */
#define UART_XR_EFR 9   /* I/O: Extended Features Register (XR17D15x) */
#define UART_EFR_CTS        0x80 /* CTS flow control */
#define UART_EFR_RTS        0x40 /* RTS flow control */
#define UART_EFR_SCD        0x20 /* Special character detect */
#define UART_EFR_ECB        0x10 /* Enhanced control bit */
/*
 * the low four bits control software flow control
 */

/*
 * LCR=0xBF, TI16C752, ST16650, ST16650A, ST16654
 */
#define UART_XON1   4   /* I/O: Xon character 1 */
#define UART_XON2   5   /* I/O: Xon character 2 */
#define UART_XOFF1  6   /* I/O: Xoff character 1 */
#define UART_XOFF2  7   /* I/O: Xoff character 2 */

/*
 * EFR[4]=1 MCR[6]=1, TI16C752
 */
#define UART_TI752_TCR  6   /* I/O: transmission control register */
#define UART_TI752_TLR  7   /* I/O: trigger level register */

/*
 * LCR=0xBF, XR16C85x
 */
#define UART_TRG    0   /* FCTR bit 7 selects Rx or Tx
                 * In: Fifo count
                 * Out: Fifo custom trigger levels */
/*
 * These are the definitions for the Programmable Trigger Register
 */
#define UART_TRG_1      0x01
#define UART_TRG_4      0x04
#define UART_TRG_8      0x08
#define UART_TRG_16     0x10
#define UART_TRG_32     0x20
#define UART_TRG_64     0x40
#define UART_TRG_96     0x60
#define UART_TRG_120        0x78
#define UART_TRG_128        0x80

#define UART_FCTR   1   /* Feature Control Register */
#define UART_FCTR_RTS_NODELAY   0x00  /* RTS flow control delay */
#define UART_FCTR_RTS_4DELAY    0x01
#define UART_FCTR_RTS_6DELAY    0x02
#define UART_FCTR_RTS_8DELAY    0x03
#define UART_FCTR_IRDA      0x04  /* IrDa data encode select */
#define UART_FCTR_TX_INT    0x08  /* Tx interrupt type select */
#define UART_FCTR_TRGA      0x00  /* Tx/Rx 550 trigger table select */
#define UART_FCTR_TRGB      0x10  /* Tx/Rx 650 trigger table select */
#define UART_FCTR_TRGC      0x20  /* Tx/Rx 654 trigger table select */
#define UART_FCTR_TRGD      0x30  /* Tx/Rx 850 programmable trigger select */
#define UART_FCTR_SCR_SWAP  0x40  /* Scratch pad register swap */
#define UART_FCTR_RX        0x00  /* Programmable trigger mode select */
#define UART_FCTR_TX        0x80  /* Programmable trigger mode select */

/*
 * LCR=0xBF, FCTR[6]=1
 */
#define UART_EMSR   7   /* Extended Mode Select Register */
#define UART_EMSR_FIFO_COUNT    0x01  /* Rx/Tx select */
#define UART_EMSR_ALT_COUNT 0x02  /* Alternating count select */

/*
 * The Intel XScale on-chip UARTs define these bits
 */
#define UART_IER_DMAE   0x80    /* DMA Requests Enable */
#define UART_IER_UUE    0x40    /* UART Unit Enable */
#define UART_IER_NRZE   0x20    /* NRZ coding Enable */
#define UART_IER_RTOIE  0x10    /* Receiver Time Out Interrupt Enable */

#define UART_IIR_TOD    0x08    /* Character Timeout Indication Detected */

#define UART_FCR_PXAR1  0x00    /* receive FIFO threshold = 1 */
#define UART_FCR_PXAR8  0x40    /* receive FIFO threshold = 8 */
#define UART_FCR_PXAR16 0x80    /* receive FIFO threshold = 16 */
#define UART_FCR_PXAR32 0xc0    /* receive FIFO threshold = 32 */

/*
 * Intel MID on-chip HSU (High Speed UART) defined bits
 */
#define UART_FCR_HSU_64_1B  0x00    /* receive FIFO treshold = 1 */
#define UART_FCR_HSU_64_16B 0x40    /* receive FIFO treshold = 16 */
#define UART_FCR_HSU_64_32B 0x80    /* receive FIFO treshold = 32 */
#define UART_FCR_HSU_64_56B 0xc0    /* receive FIFO treshold = 56 */

#define UART_FCR_HSU_16_1B  0x00    /* receive FIFO treshold = 1 */
#define UART_FCR_HSU_16_4B  0x40    /* receive FIFO treshold = 4 */
#define UART_FCR_HSU_16_8B  0x80    /* receive FIFO treshold = 8 */
#define UART_FCR_HSU_16_14B 0xc0    /* receive FIFO treshold = 14 */

#define UART_FCR_HSU_64B_FIFO   0x20    /* chose 64 bytes FIFO */
#define UART_FCR_HSU_16B_FIFO   0x00    /* chose 16 bytes FIFO */

#define UART_FCR_HALF_EMPT_TXI  0x00    /* trigger TX_EMPT IRQ for half empty */
#define UART_FCR_FULL_EMPT_TXI  0x08    /* trigger TX_EMPT IRQ for full empty */

/*
 * These register definitions are for the 16C950
 */
#define UART_ASR    0x01    /* Additional Status Register */
#define UART_RFL    0x03    /* Receiver FIFO level */
#define UART_TFL    0x04    /* Transmitter FIFO level */
#define UART_ICR    0x05    /* Index Control Register */

/* The 16950 ICR registers */
#define UART_ACR    0x00    /* Additional Control Register */
#define UART_CPR    0x01    /* Clock Prescalar Register */
#define UART_TCR    0x02    /* Times Clock Register */
#define UART_CKS    0x03    /* Clock Select Register */
#define UART_TTL    0x04    /* Transmitter Interrupt Trigger Level */
#define UART_RTL    0x05    /* Receiver Interrupt Trigger Level */
#define UART_FCL    0x06    /* Flow Control Level Lower */
#define UART_FCH    0x07    /* Flow Control Level Higher */
#define UART_ID1    0x08    /* ID #1 */
#define UART_ID2    0x09    /* ID #2 */
#define UART_ID3    0x0A    /* ID #3 */
#define UART_REV    0x0B    /* Revision */
#define UART_CSR    0x0C    /* Channel Software Reset */
#define UART_NMR    0x0D    /* Nine-bit Mode Register */
#define UART_CTR    0xFF

/*
 * The 16C950 Additional Control Register
 */
#define UART_ACR_RXDIS  0x01    /* Receiver disable */
#define UART_ACR_TXDIS  0x02    /* Transmitter disable */
#define UART_ACR_DSRFC  0x04    /* DSR Flow Control */
#define UART_ACR_TLENB  0x20    /* 950 trigger levels enable */
#define UART_ACR_ICRRD  0x40    /* ICR Read enable */
#define UART_ACR_ASREN  0x80    /* Additional status enable */



/*
 * These definitions are for the RSA-DV II/S card, from
 *
 * Kiyokazu SUTO <[email protected]>
 */

#define UART_RSA_BASE (-8)

#define UART_RSA_MSR ((UART_RSA_BASE) + 0) /* I/O: Mode Select Register */

#define UART_RSA_MSR_SWAP (1 << 0) /* Swap low/high 8 bytes in I/O port addr */
#define UART_RSA_MSR_FIFO (1 << 2) /* Enable the external FIFO */
#define UART_RSA_MSR_FLOW (1 << 3) /* Enable the auto RTS/CTS flow control */
#define UART_RSA_MSR_ITYP (1 << 4) /* Level (1) / Edge triger (0) */

#define UART_RSA_IER ((UART_RSA_BASE) + 1) /* I/O: Interrupt Enable Register */

#define UART_RSA_IER_Rx_FIFO_H (1 << 0) /* Enable Rx FIFO half full int. */
#define UART_RSA_IER_Tx_FIFO_H (1 << 1) /* Enable Tx FIFO half full int. */
#define UART_RSA_IER_Tx_FIFO_E (1 << 2) /* Enable Tx FIFO empty int. */
#define UART_RSA_IER_Rx_TOUT (1 << 3) /* Enable char receive timeout int */
#define UART_RSA_IER_TIMER (1 << 4) /* Enable timer interrupt */

#define UART_RSA_SRR ((UART_RSA_BASE) + 2) /* IN: Status Read Register */

#define UART_RSA_SRR_Tx_FIFO_NEMP (1 << 0) /* Tx FIFO is not empty (1) */
#define UART_RSA_SRR_Tx_FIFO_NHFL (1 << 1) /* Tx FIFO is not half full (1) */
#define UART_RSA_SRR_Tx_FIFO_NFUL (1 << 2) /* Tx FIFO is not full (1) */
#define UART_RSA_SRR_Rx_FIFO_NEMP (1 << 3) /* Rx FIFO is not empty (1) */
#define UART_RSA_SRR_Rx_FIFO_NHFL (1 << 4) /* Rx FIFO is not half full (1) */
#define UART_RSA_SRR_Rx_FIFO_NFUL (1 << 5) /* Rx FIFO is not full (1) */
#define UART_RSA_SRR_Rx_TOUT (1 << 6) /* Character reception timeout occurred (1) */
#define UART_RSA_SRR_TIMER (1 << 7) /* Timer interrupt occurred */

#define UART_RSA_FRR ((UART_RSA_BASE) + 2) /* OUT: FIFO Reset Register */

#define UART_RSA_TIVSR ((UART_RSA_BASE) + 3) /* I/O: Timer Interval Value Set Register */

#define UART_RSA_TCR ((UART_RSA_BASE) + 4) /* OUT: Timer Control Register */

#define UART_RSA_TCR_SWITCH (1 << 0) /* Timer on */

/*
 * The RSA DSV/II board has two fixed clock frequencies.  One is the
 * standard rate, and the other is 8 times faster.
 */
#define SERIAL_RSA_BAUD_BASE (921600)
#define SERIAL_RSA_BAUD_BASE_LO (SERIAL_RSA_BAUD_BASE / 8)

/*
 * Extra serial register definitions for the internal UARTs
 * in TI OMAP processors.
 */
#define UART_OMAP_MDR1      0x08    /* Mode definition register */
#define UART_OMAP_MDR2      0x09    /* Mode definition register 2 */
#define UART_OMAP_SCR       0x10    /* Supplementary control register */
#define UART_OMAP_SSR       0x11    /* Supplementary status register */
#define UART_OMAP_EBLR      0x12    /* BOF length register */
#define UART_OMAP_OSC_12M_SEL   0x13    /* OMAP1510 12MHz osc select */
#define UART_OMAP_MVER      0x14    /* Module version register */
#define UART_OMAP_SYSC      0x15    /* System configuration register */
#define UART_OMAP_SYSS      0x16    /* System status register */
#define UART_OMAP_WER       0x17    /* Wake-up enable register */

/*
 * These are the definitions for the MDR1 register
 */
#define UART_OMAP_MDR1_16X_MODE     0x00    /* UART 16x mode */
#define UART_OMAP_MDR1_SIR_MODE     0x01    /* SIR mode */
#define UART_OMAP_MDR1_16X_ABAUD_MODE   0x02    /* UART 16x auto-baud */
#define UART_OMAP_MDR1_13X_MODE     0x03    /* UART 13x mode */
#define UART_OMAP_MDR1_MIR_MODE     0x04    /* MIR mode */
#define UART_OMAP_MDR1_FIR_MODE     0x05    /* FIR mode */
#define UART_OMAP_MDR1_CIR_MODE     0x06    /* CIR mode */
#define UART_OMAP_MDR1_DISABLE      0x07    /* Disable (default state) */

#endif /* _LINUX_SERIAL_REG_H */