z8530.h

Go to the documentation of this file.

/* 8530 Serial Communications Controller Register definitions */
#define FLAG    0x7e

/* Write Register 0 */
#define R0  0       /* Register selects */
#define R1  1
#define R2  2
#define R3  3
#define R4  4
#define R5  5
#define R6  6
#define R7  7
#define R8  8
#define R9  9
#define R10 10
#define R11 11
#define R12 12
#define R13 13
#define R14 14
#define R15 15

#define NULLCODE    0   /* Null Code */
#define POINT_HIGH  0x8 /* Select upper half of registers */
#define RES_EXT_INT 0x10    /* Reset Ext. Status Interrupts */
#define SEND_ABORT  0x18    /* HDLC Abort */
#define RES_RxINT_FC    0x20    /* Reset RxINT on First Character */
#define RES_Tx_P    0x28    /* Reset TxINT Pending */
#define ERR_RES     0x30    /* Error Reset */
#define RES_H_IUS   0x38    /* Reset highest IUS */

#define RES_Rx_CRC  0x40    /* Reset Rx CRC Checker */
#define RES_Tx_CRC  0x80    /* Reset Tx CRC Checker */
#define RES_EOM_L   0xC0    /* Reset EOM latch */

/* Write Register 1 */

#define EXT_INT_ENAB    0x1 /* Ext Int Enable */
#define TxINT_ENAB  0x2 /* Tx Int Enable */
#define PAR_SPEC    0x4 /* Parity is special condition */

#define RxINT_DISAB 0   /* Rx Int Disable */
#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
#define INT_ALL_Rx  0x10    /* Int on all Rx Characters or error */
#define INT_ERR_Rx  0x18    /* Int on error only */

#define WT_RDY_RT   0x20    /* Wait/Ready on R/T */
#define WT_FN_RDYFN 0x40    /* Wait/FN/Ready FN */
#define WT_RDY_ENAB 0x80    /* Wait/Ready Enable */

/* Write Register #2 (Interrupt Vector) */

/* Write Register 3 */

#define RxENABLE    0x1 /* Rx Enable */
#define SYNC_L_INH  0x2 /* Sync Character Load Inhibit */
#define ADD_SM      0x4 /* Address Search Mode (SDLC) */
#define RxCRC_ENAB  0x8 /* Rx CRC Enable */
#define ENT_HM      0x10    /* Enter Hunt Mode */
#define AUTO_ENAB   0x20    /* Auto Enables */
#define Rx5     0x0 /* Rx 5 Bits/Character */
#define Rx7     0x40    /* Rx 7 Bits/Character */
#define Rx6     0x80    /* Rx 6 Bits/Character */
#define Rx8     0xc0    /* Rx 8 Bits/Character */

/* Write Register 4 */

#define PAR_ENA     0x1 /* Parity Enable */
#define PAR_EVEN    0x2 /* Parity Even/Odd* */

#define SYNC_ENAB   0   /* Sync Modes Enable */
#define SB1     0x4 /* 1 stop bit/char */
#define SB15        0x8 /* 1.5 stop bits/char */
#define SB2     0xc /* 2 stop bits/char */

#define MONSYNC     0   /* 8 Bit Sync character */
#define BISYNC      0x10    /* 16 bit sync character */
#define SDLC        0x20    /* SDLC Mode (01111110 Sync Flag) */
#define EXTSYNC     0x30    /* External Sync Mode */

#define X1CLK       0x0 /* x1 clock mode */
#define X16CLK      0x40    /* x16 clock mode */
#define X32CLK      0x80    /* x32 clock mode */
#define X64CLK      0xC0    /* x64 clock mode */

/* Write Register 5 */

#define TxCRC_ENAB  0x1 /* Tx CRC Enable */
#define RTS     0x2 /* RTS */
#define SDLC_CRC    0x4 /* SDLC/CRC-16 */
#define TxENAB      0x8 /* Tx Enable */
#define SND_BRK     0x10    /* Send Break */
#define Tx5     0x0 /* Tx 5 bits (or less)/character */
#define Tx7     0x20    /* Tx 7 bits/character */
#define Tx6     0x40    /* Tx 6 bits/character */
#define Tx8     0x60    /* Tx 8 bits/character */
#define DTR     0x80    /* DTR */

/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */

/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */

/* Write Register 8 (transmit buffer) */

/* Write Register 9 (Master interrupt control) */
#define VIS 1   /* Vector Includes Status */
#define NV  2   /* No Vector */
#define DLC 4   /* Disable Lower Chain */
#define MIE 8   /* Master Interrupt Enable */
#define STATHI  0x10    /* Status high */
#define NORESET 0   /* No reset on write to R9 */
#define CHRB    0x40    /* Reset channel B */
#define CHRA    0x80    /* Reset channel A */
#define FHWRES  0xc0    /* Force hardware reset */

/* Write Register 10 (misc control bits) */
#define BIT6    1   /* 6 bit/8bit sync */
#define LOOPMODE 2  /* SDLC Loop mode */
#define ABUNDER 4   /* Abort/flag on SDLC xmit underrun */
#define MARKIDLE 8  /* Mark/flag on idle */
#define GAOP    0x10    /* Go active on poll */
#define NRZ 0   /* NRZ mode */
#define NRZI    0x20    /* NRZI mode */
#define FM1 0x40    /* FM1 (transition = 1) */
#define FM0 0x60    /* FM0 (transition = 0) */
#define CRCPS   0x80    /* CRC Preset I/O */

/* Write Register 11 (Clock Mode control) */
#define TRxCXT  0   /* TRxC = Xtal output */
#define TRxCTC  1   /* TRxC = Transmit clock */
#define TRxCBR  2   /* TRxC = BR Generator Output */
#define TRxCDP  3   /* TRxC = DPLL output */
#define TRxCOI  4   /* TRxC O/I */
#define TCRTxCP 0   /* Transmit clock = RTxC pin */
#define TCTRxCP 8   /* Transmit clock = TRxC pin */
#define TCBR    0x10    /* Transmit clock = BR Generator output */
#define TCDPLL  0x18    /* Transmit clock = DPLL output */
#define RCRTxCP 0   /* Receive clock = RTxC pin */
#define RCTRxCP 0x20    /* Receive clock = TRxC pin */
#define RCBR    0x40    /* Receive clock = BR Generator output */
#define RCDPLL  0x60    /* Receive clock = DPLL output */
#define RTxCX   0x80    /* RTxC Xtal/No Xtal */

/* Write Register 12 (lower byte of baud rate generator time constant) */

/* Write Register 13 (upper byte of baud rate generator time constant) */

/* Write Register 14 (Misc control bits) */
#define BRENABL 1   /* Baud rate generator enable */
#define BRSRC   2   /* Baud rate generator source */
#define DTRREQ  4   /* DTR/Request function */
#define AUTOECHO 8  /* Auto Echo */
#define LOOPBAK 0x10    /* Local loopback */
#define SEARCH  0x20    /* Enter search mode */
#define RMC 0x40    /* Reset missing clock */
#define DISDPLL 0x60    /* Disable DPLL */
#define SSBR    0x80    /* Set DPLL source = BR generator */
#define SSRTxC  0xa0    /* Set DPLL source = RTxC */
#define SFMM    0xc0    /* Set FM mode */
#define SNRZI   0xe0    /* Set NRZI mode */

/* Write Register 15 (external/status interrupt control) */
#define ZCIE    2   /* Zero count IE */
#define DCDIE   8   /* DCD IE */
#define SYNCIE  0x10    /* Sync/hunt IE */
#define CTSIE   0x20    /* CTS IE */
#define TxUIE   0x40    /* Tx Underrun/EOM IE */
#define BRKIE   0x80    /* Break/Abort IE */


/* Read Register 0 */
#define Rx_CH_AV    0x1 /* Rx Character Available */
#define ZCOUNT      0x2 /* Zero count */
#define Tx_BUF_EMP  0x4 /* Tx Buffer empty */
#define DCD     0x8 /* DCD */
#define SYNC_HUNT   0x10    /* Sync/hunt */
#define CTS     0x20    /* CTS */
#define TxEOM       0x40    /* Tx underrun */
#define BRK_ABRT    0x80    /* Break/Abort */

/* Read Register 1 */
#define ALL_SNT     0x1 /* All sent */
/* Residue Data for 8 Rx bits/char programmed */
#define RES3        0x8 /* 0/3 */
#define RES4        0x4 /* 0/4 */
#define RES5        0xc /* 0/5 */
#define RES6        0x2 /* 0/6 */
#define RES7        0xa /* 0/7 */
#define RES8        0x6 /* 0/8 */
#define RES18       0xe /* 1/8 */
#define RES28       0x0 /* 2/8 */
/* Special Rx Condition Interrupts */
#define PAR_ERR     0x10    /* Parity error */
#define Rx_OVR      0x20    /* Rx Overrun Error */
#define CRC_ERR     0x40    /* CRC/Framing Error */
#define END_FR      0x80    /* End of Frame (SDLC) */

/* Read Register 2 (channel b only) - Interrupt vector */

/* Read Register 3 (interrupt pending register) ch a only */
#define CHBEXT  0x1     /* Channel B Ext/Stat IP */
#define CHBTxIP 0x2     /* Channel B Tx IP */
#define CHBRxIP 0x4     /* Channel B Rx IP */
#define CHAEXT  0x8     /* Channel A Ext/Stat IP */
#define CHATxIP 0x10        /* Channel A Tx IP */
#define CHARxIP 0x20        /* Channel A Rx IP */

/* Read Register 8 (receive data register) */

/* Read Register 10  (misc status bits) */
#define ONLOOP  2       /* On loop */
#define LOOPSEND 0x10       /* Loop sending */
#define CLK2MIS 0x40        /* Two clocks missing */
#define CLK1MIS 0x80        /* One clock missing */

/* Read Register 12 (lower byte of baud rate generator constant) */

/* Read Register 13 (upper byte of baud rate generator constant) */

/* Read Register 15 (value of WR 15) */

/* Z85C30/Z85230 Enhanced SCC register definitions */

/* Write Register 7' (SDLC/HDLC Programmable Enhancements) */
#define AUTOTXF 0x01        /* Auto Tx Flag */
#define AUTOEOM 0x02        /* Auto EOM Latch Reset */
#define AUTORTS 0x04        /* Auto RTS */
#define TXDNRZI 0x08        /* TxD Pulled High in SDLC NRZI mode */
#define RXFIFOH 0x08        /* Z85230: Int on RX FIFO half full */
#define FASTDTR 0x10        /* Fast DTR/REQ Mode */
#define CRCCBCR 0x20        /* CRC Check Bytes Completely Received */
#define TXFIFOE 0x20        /* Z85230: Int on TX FIFO completely empty */
#define EXTRDEN 0x40        /* Extended Read Enabled */

/* Write Register 15 (external/status interrupt control) */
#define SHDLCE  1       /* SDLC/HDLC Enhancements Enable */
#define FIFOE   4       /* FIFO Enable */

/* Read Register 6 (frame status FIFO) */
#define BCLSB   0xff        /* LSB of 14 bits count */

/* Read Register 7 (frame status FIFO) */
#define BCMSB   0x3f        /* MSB of 14 bits count */
#define FDA 0x40        /* FIFO Data Available Status */
#define FOS 0x80        /* FIFO Overflow Status */