System Administration Guide: IP Services

How to Protect a VPN With an IPsec Tunnel in Tunnel Mode Over IPv6

To set up a VPN on an IPv6 network, you follow the same steps as for an IPv4 network. However, the syntax of the commands is slightly different. For a fuller description of the reasons for running particular commands, see How to Protect a VPN With an IPsec Tunnel in Tunnel Mode Over IPv4.

This procedure uses the following configuration parameters.

Parameter	Europe	California
System name	enigma	partym
System intranet interface	hme1	hme1
System Internet interface	hme0	hme0
System intranet address	6000:6666::aaaa:1116	6000:3333::eeee:1113
System Internet address	2001::aaaa:6666:6666	2001::eeee:3333:3333
Name of Internet router	router-E	router-C
Address of Internet router	2001::aaaa:0:4	2001::eeee:0:1
Tunnel name	ip6.tun0	ip6.tun0

On the system console on one of the systems, assume the Primary Administrator role or become superuser.
The Primary Administrator role includes the Primary Administrator profile. To create the role and assign the role to a user, see Chapter 2, "Working With the Solaris Management Console (Tasks)," in System Administration Guide: Basic Administration.

Note - Logging in remotely exposes security-critical traffic to eavesdropping. Even if you somehow protect the remote login, the security of the system is reduced to the security of the remote login session.

Control the flow of packets before configuring IPsec.

For the effects of these commands, see Step 2 in How to Protect a VPN With an IPsec Tunnel in Tunnel Mode Over IPv4.

Ensure that IP forwarding and IP dynamic routing are disabled.

# routeadm
Configuration       Current         Current
       Option       Configuration  System State
--------------------------------------------------
...
IPv6 forwarding     disabled          disabled
   IPv6 routing     disabled          disabled

If forwarding and routing are enabled, you can disable them by typing:

# routeadm -d ipv6-forwarding -d ipv6-routing
# routeadm -u

Turn on IP strict destination multihoming.

# ndd -set /dev/ip ip6_strict_dst_multihoming 1

Disable most network services, and possibly all network services.

Note - If your system was installed with the "limited" SMF profile, then you can skip this step. Network services, with the exception of Solaris Secure Shell, are disabled.

The disabling of network services prevents IP packets from doing any harm to the system. For example, an SNMP daemon, a telnet connection, or an rlogin connection could be exploited.

You have two options.

Run the "limited" SMF profile.
# netservices limited

Or, individually disable network services.

# svcadm disable network/ftp:default
# svcadm disable network/finger:default
# svcadm disable network/login:rlogin
# svcadm disable network/nfs/server:default
# svcadm disable network/rpc/rstat:default
# svcadm disable network/smtp:sendmail
# svcadm disable network/telnet:default
# svcs | grep network
online         Aug_02   svc:/network/loopback:default
...
online         Aug_09   svc:/network/ssh:default
...

On each system, add a pair of SAs between the two systems.
Choose one of the following options.
- Configure IKE to manage the keys for the SAs. Use one of the procedures in Configuring IKE (Task Map) to configure IKE for the VPN.
- If you have an overriding reason to manually manage the keys, see How to Manually Create IPsec Security Associations.

On each system, add IPsec policy.

Edit the /etc/inet/ipsecinit.conf file to add the IPsec policy for the VPN.

For example, on the enigma system, type the following entry into the ipsecinit.conf file:

# IPv6 Neighbor Discovery messages bypass IPsec.
{ulp ipv6-icmp type 133-137 dir both} pass {}

# LAN traffic to and from this host can bypass IPsec.
{laddr 6000:6666::aaaa:1116 dir both} bypass {}

# WAN traffic uses ESP with 3DES and MD5.
{tunnel ip6.tun0 negotiate tunnel} 
  ipsec {encr_algs 3des encr_auth_algs md5 sa shared}

On the partym system, type the following entry into the ipsecinit.conf file:

# IPv6 Neighbor Discovery messages bypass IPsec.
{ulp ipv6-icmp type 133-137 dir both} pass {}

# LAN traffic to and from this host can bypass IPsec.
{laddr 6000:3333::eeee:1113 dir both} bypass {}

# WAN traffic uses ESP with 3DES and MD5.
{tunnel ip6.tun0 negotiate tunnel} 
  ipsec {encr_algs 3des encr_auth_algs md5 sa shared}

On each system, configure a secure tunnel, ip6.tun0.

For example, on the enigma system, type the following commands:

# ifconfig ip6.tun0 inet6 plumb

# ifconfig ip6.tun0 inet6 6000:6666::aaaa:1116 6000:3333::eeee:1113 \
tsrc 2001::aaaa:6666:6666   tdst 2001::eeee:3333:3333

On the partym system, type the following commands:

# ifconfig ip6.tun0 inet6 plumb

# ifconfig ip6.tun0 inet6 6000:3333::eeee:1113 6000:6666::aaaa:1116 \
tsrc 2001::eeee:3333:3333   tdst 2001::aaaa:6666:6666

Protect the tunnel with the IPsec policy that you created.
# ipsecconf
Bring up the router for the tunnel.
# ifconfig ip6.tun0 router up
On each system, turn on IP forwarding for the hme1 interface.
# ifconfig hme1 router
On each system, ensure that routing protocols do not advertise the default route within the intranet.
# ifconfig hme0 private
Manually, add a default route over hme0.
1. For example, on the enigma system, add the following route:
  # route add -inet6 default 2001::aaaa:0:4
2. On the partym system, add the following route:
  # route add -inet6 default 2001::eeee:0:1
Ensure that the VPN starts after a reboot by adding an entry to the /etc/hostname6.ip6.tun0 file.
The entry replicates the parameters that were passed to the ifconfig command in Step 5.
1. For example, on the enigma system, add the following entry to the hostname6.ip6.tun0 file:
  6000:6666::aaaa:1116 6000:3333::eeee:1113 \ tsrc 2001::aaaa:6666:6666 tdst 2001::eeee:3333:3333 router up
2. On the partym system, add the following entry to the hostname6.ip6.tun0 file:
  6000:3333::eeee:1113 6000:6666::aaaa:1116 \ tsrc 2001::eeee:3333:3333 tdst 2001::aaaa:6666:6666 router up

On each system, configure the interface files to pass the correct parameters to the routing daemon.

On the enigma system, modify the /etc/hostname6.interface files.

# cat enigma hostname6.hme0
6000:6666::aaaa:1116 inet6 private

#  cat enigma hostname6.hme1
2001::aaaa:6666:6666 inet6 router

On the partym system, modify the /etc/hostname6.interface files.

# cat partym hostname6.hme0
6000:3333::eeee:1113 inet6 private

# cat partym hostname6.hme1
2001::eeee:3333:3333 inet6 router

On each system, run a routing protocol.

# routeadm -e ipv6-routing
# routeadm -u