The proxy server takes each request and looks up locations
for the account, container, or object and routes the requests
correctly. The proxy server also handles API requests. You
enable account management by configuring it in the
/etc/swift/proxy-server.conf
file.
Note | |
---|---|
The Object Storage processes run under a separate user
and group, set by configuration options, and referred to as
|
Install swift-proxy service:
# yum install openstack-swift-proxy memcached python-swiftclient python-keystone-auth-token
Modify memcached to listen on the default interface on a local, non-public network. Edit the
/etc/sysconfig/memcached
file:OPTIONS="-l
PROXY_LOCAL_NET_IP
"Start the memcached service and configure it to start when the system boots:
# service memcached start # chkconfig memcached on
Edit
/etc/swift/proxy-server.conf
:[DEFAULT] bind_port = 8080 user = swift [pipeline:main] pipeline = healthcheck cache authtoken keystoneauth proxy-server [app:proxy-server] use = egg:swift#proxy allow_account_management = true account_autocreate = true [filter:keystoneauth] use = egg:swift#keystoneauth operator_roles = Member,admin,swiftoperator [filter:authtoken] paste.filter_factory = keystoneclient.middleware.auth_token:filter_factory # Delaying the auth decision is required to support token-less # usage for anonymous referrers ('.r:*'). delay_auth_decision = true # cache directory for signing certificate signing_dir = /home/swift/keystone-signing # auth_* settings refer to the Keystone server auth_protocol = http auth_host =
controller
auth_port = 35357 # the service tenant and swift username and password created in Keystone admin_tenant_name = service admin_user = swift admin_password =SWIFT_PASS
[filter:cache] use = egg:swift#memcache [filter:catch_errors] use = egg:swift#catch_errors [filter:healthcheck] use = egg:swift#healthcheckNote If you run multiple memcache servers, put the multiple IP:port listings in the [filter:cache] section of the
/etc/swift/proxy-server.conf
file:10.1.2.3:11211,10.1.2.4:11211
Only the proxy server uses memcache.
Create the account, container, and object rings. The builder command creates a builder file with a few parameters. The parameter with the value of 18 represents 2 ^ 18th, the value that the partition is sized to. Set this “partition power” value based on the total amount of storage you expect your entire ring to use. The value 3 represents the number of replicas of each object, with the last value being the number of hours to restrict moving a partition more than once.
# cd /etc/swift # swift-ring-builder account.builder create 18 3 1 # swift-ring-builder container.builder create 18 3 1 # swift-ring-builder object.builder create 18 3 1
For every storage device on each node add entries to each ring:
# swift-ring-builder account.builder add z
ZONE
-STORAGE_LOCAL_NET_IP
:6002[RSTORAGE_REPLICATION_NET_IP
:6005]/DEVICE
100 # swift-ring-builder container.builder add zZONE
-STORAGE_LOCAL_NET_IP_1
:6001[RSTORAGE_REPLICATION_NET_IP
:6004]/DEVICE
100 # swift-ring-builder object.builder add zZONE
-STORAGE_LOCAL_NET_IP_1
:6000[RSTORAGE_REPLICATION_NET_IP
:6003]/DEVICE
100Note You must omit the optional
STORAGE_REPLICATION_NET_IP
parameter if you do not want to use dedicated network for replication.For example, if a storage node has a partition in Zone 1 on IP 10.0.0.1, the storage node has address 10.0.1.1 from replication network. The mount point of this partition is
/srv/node/sdb1
, and the path in/etc/rsyncd.conf
is/srv/node/
, the DEVICE would be sdb1 and the commands are:# swift-ring-builder account.builder add z1-10.0.0.1:6002R10.0.1.1:6005/sdb1 100 # swift-ring-builder container.builder add z1-10.0.0.1:6001R10.0.1.1:6004/sdb1 100 # swift-ring-builder object.builder add z1-10.0.0.1:6000R10.0.1.1:6003/sdb1 100
Note If you assume five zones with one node for each zone, start ZONE at 1. For each additional node, increment ZONE by 1.
Verify the ring contents for each ring:
# swift-ring-builder account.builder # swift-ring-builder container.builder # swift-ring-builder object.builder
Rebalance the rings:
# swift-ring-builder account.builder rebalance # swift-ring-builder container.builder rebalance # swift-ring-builder object.builder rebalance
Note Rebalancing rings can take some time.
Copy the
account.ring.gz
,container.ring.gz
, andobject.ring.gz
files to each of the Proxy and Storage nodes in/etc/swift
.Make sure the swift user owns all configuration files:
# chown -R swift:swift /etc/swift
Start the Proxy service and configure it to start when the system boots:
# service openstack-swift-proxy start # chkconfig openstack-swift-proxy on