gtwx5715-setup.c

Go to the documentation of this file.

/*
 * arch/arm/mach-ixp4xx/gtwx5715-setup.c
 *
 * Gemtek GTWX5715 (Linksys WRV54G) board setup
 *
 * Copyright (C) 2004 George T. Joseph
 * Derived from Coyote
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version 2
 * of the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.
 *
 */

#include <linux/init.h>
#include <linux/device.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/serial_8250.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>

/* GPIO 5,6,7 and 12 are hard wired to the Kendin KS8995M Switch
   and operate as an SPI type interface.  The details of the interface
   are available on Kendin/Micrel's web site. */

#define GTWX5715_KSSPI_SELECT   5
#define GTWX5715_KSSPI_TXD  6
#define GTWX5715_KSSPI_CLOCK    7
#define GTWX5715_KSSPI_RXD  12

/* The "reset" button is wired to GPIO 3.
   The GPIO is brought "low" when the button is pushed. */

#define GTWX5715_BUTTON_GPIO    3

/* Board Label      Front Label
   LED1             Power
   LED2             Wireless-G
   LED3             not populated but could be
   LED4             Internet
   LED5 - LED8      Controlled by KS8995M Switch
   LED9             DMZ */

#define GTWX5715_LED1_GPIO  2
#define GTWX5715_LED2_GPIO  9
#define GTWX5715_LED3_GPIO  8
#define GTWX5715_LED4_GPIO  1
#define GTWX5715_LED9_GPIO  4

/*
 * Xscale UART registers are 32 bits wide with only the least
 * significant 8 bits having any meaning.  From a configuration
 * perspective, this means 2 things...
 *
 *   Setting .regshift = 2 so that the standard 16550 registers
 *   line up on every 4th byte.
 *
 *   Shifting the register start virtual address +3 bytes when
 *   compiled big-endian.  Since register writes are done on a
 *   single byte basis, if the shift isn't done the driver will
 *   write the value into the most significant byte of the register,
 *   which is ignored, instead of the least significant.
 */

#ifdef  __ARMEB__
#define REG_OFFSET  3
#else
#define REG_OFFSET  0
#endif

/*
 * Only the second or "console" uart is connected on the gtwx5715.
 */

static struct resource gtwx5715_uart_resources[] = {
    {
        .start  = IXP4XX_UART2_BASE_PHYS,
        .end    = IXP4XX_UART2_BASE_PHYS + 0x0fff,
        .flags  = IORESOURCE_MEM,
    },
    {
        .start  = IRQ_IXP4XX_UART2,
        .end    = IRQ_IXP4XX_UART2,
        .flags  = IORESOURCE_IRQ,
    },
    { },
};


static struct plat_serial8250_port gtwx5715_uart_platform_data[] = {
    {
    .mapbase    = IXP4XX_UART2_BASE_PHYS,
    .membase    = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
    .irq        = IRQ_IXP4XX_UART2,
    .flags      = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
    .iotype     = UPIO_MEM,
    .regshift   = 2,
    .uartclk    = IXP4XX_UART_XTAL,
    },
    { },
};

static struct platform_device gtwx5715_uart_device = {
    .name       = "serial8250",
    .id     = PLAT8250_DEV_PLATFORM,
    .dev            = {
        .platform_data  = gtwx5715_uart_platform_data,
    },
    .num_resources  = 2,
    .resource   = gtwx5715_uart_resources,
};

static struct flash_platform_data gtwx5715_flash_data = {
    .map_name   = "cfi_probe",
    .width      = 2,
};

static struct resource gtwx5715_flash_resource = {
    .flags      = IORESOURCE_MEM,
};

static struct platform_device gtwx5715_flash = {
    .name       = "IXP4XX-Flash",
    .id     = 0,
    .dev        = {
        .platform_data = &gtwx5715_flash_data,
    },
    .num_resources  = 1,
    .resource   = &gtwx5715_flash_resource,
};

static struct platform_device *gtwx5715_devices[] __initdata = {
    &gtwx5715_uart_device,
    &gtwx5715_flash,
};

static void __init gtwx5715_init(void)
{
    ixp4xx_sys_init();

    gtwx5715_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
    gtwx5715_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_8M - 1;

    platform_add_devices(gtwx5715_devices, ARRAY_SIZE(gtwx5715_devices));
}


MACHINE_START(GTWX5715, "Gemtek GTWX5715 (Linksys WRV54G)")
    /* Maintainer: George Joseph */
    .map_io     = ixp4xx_map_io,
    .init_early = ixp4xx_init_early,
    .init_irq   = ixp4xx_init_irq,
    .timer      = &ixp4xx_timer,
    .atag_offset    = 0x100,
    .init_machine   = gtwx5715_init,
#if defined(CONFIG_PCI)
    .dma_zone_size  = SZ_64M,
#endif
    .restart    = ixp4xx_restart,
MACHINE_END