Linux Kernel  3.7.1
 All Data Structures Namespaces Files Functions Variables Typedefs Enumerations Enumerator Macros Groups Pages
sungem.h
Go to the documentation of this file.
1 /* $Id: sungem.h,v 1.10.2.4 2002/03/11 08:54:48 davem Exp $
2  * sungem.h: Definitions for Sun GEM ethernet driver.
3  *
4  * Copyright (C) 2000 David S. Miller ([email protected])
5  */
6 
7 #ifndef _SUNGEM_H
8 #define _SUNGEM_H
9 
10 /* Global Registers */
11 #define GREG_SEBSTATE 0x0000UL /* SEB State Register */
12 #define GREG_CFG 0x0004UL /* Configuration Register */
13 #define GREG_STAT 0x000CUL /* Status Register */
14 #define GREG_IMASK 0x0010UL /* Interrupt Mask Register */
15 #define GREG_IACK 0x0014UL /* Interrupt ACK Register */
16 #define GREG_STAT2 0x001CUL /* Alias of GREG_STAT */
17 #define GREG_PCIESTAT 0x1000UL /* PCI Error Status Register */
18 #define GREG_PCIEMASK 0x1004UL /* PCI Error Mask Register */
19 #define GREG_BIFCFG 0x1008UL /* BIF Configuration Register */
20 #define GREG_BIFDIAG 0x100CUL /* BIF Diagnostics Register */
21 #define GREG_SWRST 0x1010UL /* Software Reset Register */
22 
23 /* Global SEB State Register */
24 #define GREG_SEBSTATE_ARB 0x00000003 /* State of Arbiter */
25 #define GREG_SEBSTATE_RXWON 0x00000004 /* RX won internal arbitration */
26 
27 /* Global Configuration Register */
28 #define GREG_CFG_IBURST 0x00000001 /* Infinite Burst */
29 #define GREG_CFG_TXDMALIM 0x0000003e /* TX DMA grant limit */
30 #define GREG_CFG_RXDMALIM 0x000007c0 /* RX DMA grant limit */
31 #define GREG_CFG_RONPAULBIT 0x00000800 /* Use mem read multiple for PCI read
32  * after infinite burst (Apple) */
33 #define GREG_CFG_ENBUG2FIX 0x00001000 /* Fix Rx hang after overflow */
34 
35 /* Global Interrupt Status Register.
36  *
37  * Reading this register automatically clears bits 0 through 6.
38  * This auto-clearing does not occur when the alias at GREG_STAT2
39  * is read instead. The rest of the interrupt bits only clear when
40  * the secondary interrupt status register corresponding to that
41  * bit is read (ie. if GREG_STAT_PCS is set, it will be cleared by
42  * reading PCS_ISTAT).
43  */
44 #define GREG_STAT_TXINTME 0x00000001 /* TX INTME frame transferred */
45 #define GREG_STAT_TXALL 0x00000002 /* All TX frames transferred */
46 #define GREG_STAT_TXDONE 0x00000004 /* One TX frame transferred */
47 #define GREG_STAT_RXDONE 0x00000010 /* One RX frame arrived */
48 #define GREG_STAT_RXNOBUF 0x00000020 /* No free RX buffers available */
49 #define GREG_STAT_RXTAGERR 0x00000040 /* RX tag framing is corrupt */
50 #define GREG_STAT_PCS 0x00002000 /* PCS signalled interrupt */
51 #define GREG_STAT_TXMAC 0x00004000 /* TX MAC signalled interrupt */
52 #define GREG_STAT_RXMAC 0x00008000 /* RX MAC signalled interrupt */
53 #define GREG_STAT_MAC 0x00010000 /* MAC Control signalled irq */
54 #define GREG_STAT_MIF 0x00020000 /* MIF signalled interrupt */
55 #define GREG_STAT_PCIERR 0x00040000 /* PCI Error interrupt */
56 #define GREG_STAT_TXNR 0xfff80000 /* == TXDMA_TXDONE reg val */
57 #define GREG_STAT_TXNR_SHIFT 19
58 
59 #define GREG_STAT_ABNORMAL (GREG_STAT_RXNOBUF | GREG_STAT_RXTAGERR | \
60  GREG_STAT_PCS | GREG_STAT_TXMAC | GREG_STAT_RXMAC | \
61  GREG_STAT_MAC | GREG_STAT_MIF | GREG_STAT_PCIERR)
62 
63 #define GREG_STAT_NAPI (GREG_STAT_TXALL | GREG_STAT_TXINTME | \
64  GREG_STAT_RXDONE | GREG_STAT_ABNORMAL)
65 
66 /* The layout of GREG_IMASK and GREG_IACK is identical to GREG_STAT.
67  * Bits set in GREG_IMASK will prevent that interrupt type from being
68  * signalled to the cpu. GREG_IACK can be used to clear specific top-level
69  * interrupt conditions in GREG_STAT, ie. it only works for bits 0 through 6.
70  * Setting the bit will clear that interrupt, clear bits will have no effect
71  * on GREG_STAT.
72  */
73 
74 /* Global PCI Error Status Register */
75 #define GREG_PCIESTAT_BADACK 0x00000001 /* No ACK64# during ABS64 cycle */
76 #define GREG_PCIESTAT_DTRTO 0x00000002 /* Delayed transaction timeout */
77 #define GREG_PCIESTAT_OTHER 0x00000004 /* Other PCI error, check cfg space */
78 
79 /* The layout of the GREG_PCIEMASK is identical to that of GREG_PCIESTAT.
80  * Bits set in GREG_PCIEMASK will prevent that interrupt type from being
81  * signalled to the cpu.
82  */
83 
84 /* Global BIF Configuration Register */
85 #define GREG_BIFCFG_SLOWCLK 0x00000001 /* Set if PCI runs < 25Mhz */
86 #define GREG_BIFCFG_B64DIS 0x00000002 /* Disable 64bit wide data cycle*/
87 #define GREG_BIFCFG_M66EN 0x00000004 /* Set if on 66Mhz PCI segment */
88 
89 /* Global BIF Diagnostics Register */
90 #define GREG_BIFDIAG_BURSTSM 0x007f0000 /* PCI Burst state machine */
91 #define GREG_BIFDIAG_BIFSM 0xff000000 /* BIF state machine */
92 
93 /* Global Software Reset Register.
94  *
95  * This register is used to perform a global reset of the RX and TX portions
96  * of the GEM asic. Setting the RX or TX reset bit will start the reset.
97  * The driver _MUST_ poll these bits until they clear. One may not attempt
98  * to program any other part of GEM until the bits clear.
99  */
100 #define GREG_SWRST_TXRST 0x00000001 /* TX Software Reset */
101 #define GREG_SWRST_RXRST 0x00000002 /* RX Software Reset */
102 #define GREG_SWRST_RSTOUT 0x00000004 /* Force RST# pin active */
103 #define GREG_SWRST_CACHESIZE 0x00ff0000 /* RIO only: cache line size */
104 #define GREG_SWRST_CACHE_SHIFT 16
105 
106 /* TX DMA Registers */
107 #define TXDMA_KICK 0x2000UL /* TX Kick Register */
108 #define TXDMA_CFG 0x2004UL /* TX Configuration Register */
109 #define TXDMA_DBLOW 0x2008UL /* TX Desc. Base Low */
110 #define TXDMA_DBHI 0x200CUL /* TX Desc. Base High */
111 #define TXDMA_FWPTR 0x2014UL /* TX FIFO Write Pointer */
112 #define TXDMA_FSWPTR 0x2018UL /* TX FIFO Shadow Write Pointer */
113 #define TXDMA_FRPTR 0x201CUL /* TX FIFO Read Pointer */
114 #define TXDMA_FSRPTR 0x2020UL /* TX FIFO Shadow Read Pointer */
115 #define TXDMA_PCNT 0x2024UL /* TX FIFO Packet Counter */
116 #define TXDMA_SMACHINE 0x2028UL /* TX State Machine Register */
117 #define TXDMA_DPLOW 0x2030UL /* TX Data Pointer Low */
118 #define TXDMA_DPHI 0x2034UL /* TX Data Pointer High */
119 #define TXDMA_TXDONE 0x2100UL /* TX Completion Register */
120 #define TXDMA_FADDR 0x2104UL /* TX FIFO Address */
121 #define TXDMA_FTAG 0x2108UL /* TX FIFO Tag */
122 #define TXDMA_DLOW 0x210CUL /* TX FIFO Data Low */
123 #define TXDMA_DHIT1 0x2110UL /* TX FIFO Data HighT1 */
124 #define TXDMA_DHIT0 0x2114UL /* TX FIFO Data HighT0 */
125 #define TXDMA_FSZ 0x2118UL /* TX FIFO Size */
126 
127 /* TX Kick Register.
128  *
129  * This 13-bit register is programmed by the driver to hold the descriptor
130  * entry index which follows the last valid transmit descriptor.
131  */
132 
133 /* TX Completion Register.
134  *
135  * This 13-bit register is updated by GEM to hold to descriptor entry index
136  * which follows the last descriptor already processed by GEM. Note that
137  * this value is mirrored in GREG_STAT which eliminates the need to even
138  * access this register in the driver during interrupt processing.
139  */
140 
141 /* TX Configuration Register.
142  *
143  * Note that TXDMA_CFG_FTHRESH, the TX FIFO Threshold, is an obsolete feature
144  * that was meant to be used with jumbo packets. It should be set to the
145  * maximum value of 0x4ff, else one risks getting TX MAC Underrun errors.
146  */
147 #define TXDMA_CFG_ENABLE 0x00000001 /* Enable TX DMA channel */
148 #define TXDMA_CFG_RINGSZ 0x0000001e /* TX descriptor ring size */
149 #define TXDMA_CFG_RINGSZ_32 0x00000000 /* 32 TX descriptors */
150 #define TXDMA_CFG_RINGSZ_64 0x00000002 /* 64 TX descriptors */
151 #define TXDMA_CFG_RINGSZ_128 0x00000004 /* 128 TX descriptors */
152 #define TXDMA_CFG_RINGSZ_256 0x00000006 /* 256 TX descriptors */
153 #define TXDMA_CFG_RINGSZ_512 0x00000008 /* 512 TX descriptors */
154 #define TXDMA_CFG_RINGSZ_1K 0x0000000a /* 1024 TX descriptors */
155 #define TXDMA_CFG_RINGSZ_2K 0x0000000c /* 2048 TX descriptors */
156 #define TXDMA_CFG_RINGSZ_4K 0x0000000e /* 4096 TX descriptors */
157 #define TXDMA_CFG_RINGSZ_8K 0x00000010 /* 8192 TX descriptors */
158 #define TXDMA_CFG_PIOSEL 0x00000020 /* Enable TX FIFO PIO from cpu */
159 #define TXDMA_CFG_FTHRESH 0x001ffc00 /* TX FIFO Threshold, obsolete */
160 #define TXDMA_CFG_PMODE 0x00200000 /* TXALL irq means TX FIFO empty*/
161 
162 /* TX Descriptor Base Low/High.
163  *
164  * These two registers store the 53 most significant bits of the base address
165  * of the TX descriptor table. The 11 least significant bits are always
166  * zero. As a result, the TX descriptor table must be 2K aligned.
167  */
168 
169 /* The rest of the TXDMA_* registers are for diagnostics and debug, I will document
170  * them later. -DaveM
171  */
172 
173 /* WakeOnLan Registers */
174 #define WOL_MATCH0 0x3000UL
175 #define WOL_MATCH1 0x3004UL
176 #define WOL_MATCH2 0x3008UL
177 #define WOL_MCOUNT 0x300CUL
178 #define WOL_WAKECSR 0x3010UL
179 
180 /* WOL Match count register
181  */
182 #define WOL_MCOUNT_N 0x00000010
183 #define WOL_MCOUNT_M 0x00000000 /* 0 << 8 */
185 #define WOL_WAKECSR_ENABLE 0x00000001
186 #define WOL_WAKECSR_MII 0x00000002
187 #define WOL_WAKECSR_SEEN 0x00000004
188 #define WOL_WAKECSR_FILT_UCAST 0x00000008
189 #define WOL_WAKECSR_FILT_MCAST 0x00000010
190 #define WOL_WAKECSR_FILT_BCAST 0x00000020
191 #define WOL_WAKECSR_FILT_SEEN 0x00000040
192 
193 
194 /* Receive DMA Registers */
195 #define RXDMA_CFG 0x4000UL /* RX Configuration Register */
196 #define RXDMA_DBLOW 0x4004UL /* RX Descriptor Base Low */
197 #define RXDMA_DBHI 0x4008UL /* RX Descriptor Base High */
198 #define RXDMA_FWPTR 0x400CUL /* RX FIFO Write Pointer */
199 #define RXDMA_FSWPTR 0x4010UL /* RX FIFO Shadow Write Pointer */
200 #define RXDMA_FRPTR 0x4014UL /* RX FIFO Read Pointer */
201 #define RXDMA_PCNT 0x4018UL /* RX FIFO Packet Counter */
202 #define RXDMA_SMACHINE 0x401CUL /* RX State Machine Register */
203 #define RXDMA_PTHRESH 0x4020UL /* Pause Thresholds */
204 #define RXDMA_DPLOW 0x4024UL /* RX Data Pointer Low */
205 #define RXDMA_DPHI 0x4028UL /* RX Data Pointer High */
206 #define RXDMA_KICK 0x4100UL /* RX Kick Register */
207 #define RXDMA_DONE 0x4104UL /* RX Completion Register */
208 #define RXDMA_BLANK 0x4108UL /* RX Blanking Register */
209 #define RXDMA_FADDR 0x410CUL /* RX FIFO Address */
210 #define RXDMA_FTAG 0x4110UL /* RX FIFO Tag */
211 #define RXDMA_DLOW 0x4114UL /* RX FIFO Data Low */
212 #define RXDMA_DHIT1 0x4118UL /* RX FIFO Data HighT0 */
213 #define RXDMA_DHIT0 0x411CUL /* RX FIFO Data HighT1 */
214 #define RXDMA_FSZ 0x4120UL /* RX FIFO Size */
215 
216 /* RX Configuration Register. */
217 #define RXDMA_CFG_ENABLE 0x00000001 /* Enable RX DMA channel */
218 #define RXDMA_CFG_RINGSZ 0x0000001e /* RX descriptor ring size */
219 #define RXDMA_CFG_RINGSZ_32 0x00000000 /* - 32 entries */
220 #define RXDMA_CFG_RINGSZ_64 0x00000002 /* - 64 entries */
221 #define RXDMA_CFG_RINGSZ_128 0x00000004 /* - 128 entries */
222 #define RXDMA_CFG_RINGSZ_256 0x00000006 /* - 256 entries */
223 #define RXDMA_CFG_RINGSZ_512 0x00000008 /* - 512 entries */
224 #define RXDMA_CFG_RINGSZ_1K 0x0000000a /* - 1024 entries */
225 #define RXDMA_CFG_RINGSZ_2K 0x0000000c /* - 2048 entries */
226 #define RXDMA_CFG_RINGSZ_4K 0x0000000e /* - 4096 entries */
227 #define RXDMA_CFG_RINGSZ_8K 0x00000010 /* - 8192 entries */
228 #define RXDMA_CFG_RINGSZ_BDISAB 0x00000020 /* Disable RX desc batching */
229 #define RXDMA_CFG_FBOFF 0x00001c00 /* Offset of first data byte */
230 #define RXDMA_CFG_CSUMOFF 0x000fe000 /* Skip bytes before csum calc */
231 #define RXDMA_CFG_FTHRESH 0x07000000 /* RX FIFO dma start threshold */
232 #define RXDMA_CFG_FTHRESH_64 0x00000000 /* - 64 bytes */
233 #define RXDMA_CFG_FTHRESH_128 0x01000000 /* - 128 bytes */
234 #define RXDMA_CFG_FTHRESH_256 0x02000000 /* - 256 bytes */
235 #define RXDMA_CFG_FTHRESH_512 0x03000000 /* - 512 bytes */
236 #define RXDMA_CFG_FTHRESH_1K 0x04000000 /* - 1024 bytes */
237 #define RXDMA_CFG_FTHRESH_2K 0x05000000 /* - 2048 bytes */
238 
239 /* RX Descriptor Base Low/High.
240  *
241  * These two registers store the 53 most significant bits of the base address
242  * of the RX descriptor table. The 11 least significant bits are always
243  * zero. As a result, the RX descriptor table must be 2K aligned.
244  */
245 
246 /* RX PAUSE Thresholds.
247  *
248  * These values determine when XOFF and XON PAUSE frames are emitted by
249  * GEM. The thresholds measure RX FIFO occupancy in units of 64 bytes.
250  */
251 #define RXDMA_PTHRESH_OFF 0x000001ff /* XOFF emitted w/FIFO > this */
252 #define RXDMA_PTHRESH_ON 0x001ff000 /* XON emitted w/FIFO < this */
253 
254 /* RX Kick Register.
255  *
256  * This 13-bit register is written by the host CPU and holds the last
257  * valid RX descriptor number plus one. This is, if 'N' is written to
258  * this register, it means that all RX descriptors up to but excluding
259  * 'N' are valid.
260  *
261  * The hardware requires that RX descriptors are posted in increments
262  * of 4. This means 'N' must be a multiple of four. For the best
263  * performance, the first new descriptor being posted should be (PCI)
264  * cache line aligned.
265  */
266 
267 /* RX Completion Register.
268  *
269  * This 13-bit register is updated by GEM to indicate which RX descriptors
270  * have already been used for receive frames. All descriptors up to but
271  * excluding the value in this register are ready to be processed. GEM
272  * updates this register value after the RX FIFO empties completely into
273  * the RX descriptor's buffer, but before the RX_DONE bit is set in the
274  * interrupt status register.
275  */
276 
277 /* RX Blanking Register. */
278 #define RXDMA_BLANK_IPKTS 0x000001ff /* RX_DONE asserted after this
279  * many packets received since
280  * previous RX_DONE.
281  */
282 #define RXDMA_BLANK_ITIME 0x000ff000 /* RX_DONE asserted after this
283  * many clocks (measured in 2048
284  * PCI clocks) were counted since
285  * the previous RX_DONE.
286  */
287 
288 /* RX FIFO Size.
289  *
290  * This 11-bit read-only register indicates how large, in units of 64-bytes,
291  * the RX FIFO is. The driver uses this to properly configure the RX PAUSE
292  * thresholds.
293  */
295 /* The rest of the RXDMA_* registers are for diagnostics and debug, I will document
296  * them later. -DaveM
297  */
299 /* MAC Registers */
300 #define MAC_TXRST 0x6000UL /* TX MAC Software Reset Command*/
301 #define MAC_RXRST 0x6004UL /* RX MAC Software Reset Command*/
302 #define MAC_SNDPAUSE 0x6008UL /* Send Pause Command Register */
303 #define MAC_TXSTAT 0x6010UL /* TX MAC Status Register */
304 #define MAC_RXSTAT 0x6014UL /* RX MAC Status Register */
305 #define MAC_CSTAT 0x6018UL /* MAC Control Status Register */
306 #define MAC_TXMASK 0x6020UL /* TX MAC Mask Register */
307 #define MAC_RXMASK 0x6024UL /* RX MAC Mask Register */
308 #define MAC_MCMASK 0x6028UL /* MAC Control Mask Register */
309 #define MAC_TXCFG 0x6030UL /* TX MAC Configuration Register*/
310 #define MAC_RXCFG 0x6034UL /* RX MAC Configuration Register*/
311 #define MAC_MCCFG 0x6038UL /* MAC Control Config Register */
312 #define MAC_XIFCFG 0x603CUL /* XIF Configuration Register */
313 #define MAC_IPG0 0x6040UL /* InterPacketGap0 Register */
314 #define MAC_IPG1 0x6044UL /* InterPacketGap1 Register */
315 #define MAC_IPG2 0x6048UL /* InterPacketGap2 Register */
316 #define MAC_STIME 0x604CUL /* SlotTime Register */
317 #define MAC_MINFSZ 0x6050UL /* MinFrameSize Register */
318 #define MAC_MAXFSZ 0x6054UL /* MaxFrameSize Register */
319 #define MAC_PASIZE 0x6058UL /* PA Size Register */
320 #define MAC_JAMSIZE 0x605CUL /* JamSize Register */
321 #define MAC_ATTLIM 0x6060UL /* Attempt Limit Register */
322 #define MAC_MCTYPE 0x6064UL /* MAC Control Type Register */
323 #define MAC_ADDR0 0x6080UL /* MAC Address 0 Register */
324 #define MAC_ADDR1 0x6084UL /* MAC Address 1 Register */
325 #define MAC_ADDR2 0x6088UL /* MAC Address 2 Register */
326 #define MAC_ADDR3 0x608CUL /* MAC Address 3 Register */
327 #define MAC_ADDR4 0x6090UL /* MAC Address 4 Register */
328 #define MAC_ADDR5 0x6094UL /* MAC Address 5 Register */
329 #define MAC_ADDR6 0x6098UL /* MAC Address 6 Register */
330 #define MAC_ADDR7 0x609CUL /* MAC Address 7 Register */
331 #define MAC_ADDR8 0x60A0UL /* MAC Address 8 Register */
332 #define MAC_AFILT0 0x60A4UL /* Address Filter 0 Register */
333 #define MAC_AFILT1 0x60A8UL /* Address Filter 1 Register */
334 #define MAC_AFILT2 0x60ACUL /* Address Filter 2 Register */
335 #define MAC_AF21MSK 0x60B0UL /* Address Filter 2&1 Mask Reg */
336 #define MAC_AF0MSK 0x60B4UL /* Address Filter 0 Mask Reg */
337 #define MAC_HASH0 0x60C0UL /* Hash Table 0 Register */
338 #define MAC_HASH1 0x60C4UL /* Hash Table 1 Register */
339 #define MAC_HASH2 0x60C8UL /* Hash Table 2 Register */
340 #define MAC_HASH3 0x60CCUL /* Hash Table 3 Register */
341 #define MAC_HASH4 0x60D0UL /* Hash Table 4 Register */
342 #define MAC_HASH5 0x60D4UL /* Hash Table 5 Register */
343 #define MAC_HASH6 0x60D8UL /* Hash Table 6 Register */
344 #define MAC_HASH7 0x60DCUL /* Hash Table 7 Register */
345 #define MAC_HASH8 0x60E0UL /* Hash Table 8 Register */
346 #define MAC_HASH9 0x60E4UL /* Hash Table 9 Register */
347 #define MAC_HASH10 0x60E8UL /* Hash Table 10 Register */
348 #define MAC_HASH11 0x60ECUL /* Hash Table 11 Register */
349 #define MAC_HASH12 0x60F0UL /* Hash Table 12 Register */
350 #define MAC_HASH13 0x60F4UL /* Hash Table 13 Register */
351 #define MAC_HASH14 0x60F8UL /* Hash Table 14 Register */
352 #define MAC_HASH15 0x60FCUL /* Hash Table 15 Register */
353 #define MAC_NCOLL 0x6100UL /* Normal Collision Counter */
354 #define MAC_FASUCC 0x6104UL /* First Attmpt. Succ Coll Ctr. */
355 #define MAC_ECOLL 0x6108UL /* Excessive Collision Counter */
356 #define MAC_LCOLL 0x610CUL /* Late Collision Counter */
357 #define MAC_DTIMER 0x6110UL /* Defer Timer */
358 #define MAC_PATMPS 0x6114UL /* Peak Attempts Register */
359 #define MAC_RFCTR 0x6118UL /* Receive Frame Counter */
360 #define MAC_LERR 0x611CUL /* Length Error Counter */
361 #define MAC_AERR 0x6120UL /* Alignment Error Counter */
362 #define MAC_FCSERR 0x6124UL /* FCS Error Counter */
363 #define MAC_RXCVERR 0x6128UL /* RX code Violation Error Ctr */
364 #define MAC_RANDSEED 0x6130UL /* Random Number Seed Register */
365 #define MAC_SMACHINE 0x6134UL /* State Machine Register */
367 /* TX MAC Software Reset Command. */
368 #define MAC_TXRST_CMD 0x00000001 /* Start sw reset, self-clears */
369 
370 /* RX MAC Software Reset Command. */
371 #define MAC_RXRST_CMD 0x00000001 /* Start sw reset, self-clears */
373 /* Send Pause Command. */
374 #define MAC_SNDPAUSE_TS 0x0000ffff /* The pause_time operand used in
375  * Send_Pause and flow-control
376  * handshakes.
377  */
378 #define MAC_SNDPAUSE_SP 0x00010000 /* Setting this bit instructs the MAC
379  * to send a Pause Flow Control
380  * frame onto the network.
381  */
383 /* TX MAC Status Register. */
384 #define MAC_TXSTAT_XMIT 0x00000001 /* Frame Transmitted */
385 #define MAC_TXSTAT_URUN 0x00000002 /* TX Underrun */
386 #define MAC_TXSTAT_MPE 0x00000004 /* Max Packet Size Error */
387 #define MAC_TXSTAT_NCE 0x00000008 /* Normal Collision Cntr Expire */
388 #define MAC_TXSTAT_ECE 0x00000010 /* Excess Collision Cntr Expire */
389 #define MAC_TXSTAT_LCE 0x00000020 /* Late Collision Cntr Expire */
390 #define MAC_TXSTAT_FCE 0x00000040 /* First Collision Cntr Expire */
391 #define MAC_TXSTAT_DTE 0x00000080 /* Defer Timer Expire */
392 #define MAC_TXSTAT_PCE 0x00000100 /* Peak Attempts Cntr Expire */
394 /* RX MAC Status Register. */
395 #define MAC_RXSTAT_RCV 0x00000001 /* Frame Received */
396 #define MAC_RXSTAT_OFLW 0x00000002 /* Receive Overflow */
397 #define MAC_RXSTAT_FCE 0x00000004 /* Frame Cntr Expire */
398 #define MAC_RXSTAT_ACE 0x00000008 /* Align Error Cntr Expire */
399 #define MAC_RXSTAT_CCE 0x00000010 /* CRC Error Cntr Expire */
400 #define MAC_RXSTAT_LCE 0x00000020 /* Length Error Cntr Expire */
401 #define MAC_RXSTAT_VCE 0x00000040 /* Code Violation Cntr Expire */
402 
403 /* MAC Control Status Register. */
404 #define MAC_CSTAT_PRCV 0x00000001 /* Pause Received */
405 #define MAC_CSTAT_PS 0x00000002 /* Paused State */
406 #define MAC_CSTAT_NPS 0x00000004 /* Not Paused State */
407 #define MAC_CSTAT_PTR 0xffff0000 /* Pause Time Received */
408 
409 /* The layout of the MAC_{TX,RX,C}MASK registers is identical to that
410  * of MAC_{TX,RX,C}STAT. Bits set in MAC_{TX,RX,C}MASK will prevent
411  * that interrupt type from being signalled to front end of GEM. For
412  * the interrupt to actually get sent to the cpu, it is necessary to
413  * properly set the appropriate GREG_IMASK_{TX,RX,}MAC bits as well.
414  */
416 /* TX MAC Configuration Register.
417  *
418  * NOTE: The TX MAC Enable bit must be cleared and polled until
419  * zero before any other bits in this register are changed.
420  *
421  * Also, enabling the Carrier Extension feature of GEM is
422  * a 3 step process 1) Set TX Carrier Extension 2) Set
423  * RX Carrier Extension 3) Set Slot Time to 0x200. This
424  * mode must be enabled when in half-duplex at 1Gbps, else
425  * it must be disabled.
426  */
427 #define MAC_TXCFG_ENAB 0x00000001 /* TX MAC Enable */
428 #define MAC_TXCFG_ICS 0x00000002 /* Ignore Carrier Sense */
429 #define MAC_TXCFG_ICOLL 0x00000004 /* Ignore Collisions */
430 #define MAC_TXCFG_EIPG0 0x00000008 /* Enable IPG0 */
431 #define MAC_TXCFG_NGU 0x00000010 /* Never Give Up */
432 #define MAC_TXCFG_NGUL 0x00000020 /* Never Give Up Limit */
433 #define MAC_TXCFG_NBO 0x00000040 /* No Backoff */
434 #define MAC_TXCFG_SD 0x00000080 /* Slow Down */
435 #define MAC_TXCFG_NFCS 0x00000100 /* No FCS */
436 #define MAC_TXCFG_TCE 0x00000200 /* TX Carrier Extension */
438 /* RX MAC Configuration Register.
439  *
440  * NOTE: The RX MAC Enable bit must be cleared and polled until
441  * zero before any other bits in this register are changed.
442  *
443  * Similar rules apply to the Hash Filter Enable bit when
444  * programming the hash table registers, and the Address Filter
445  * Enable bit when programming the address filter registers.
446  */
447 #define MAC_RXCFG_ENAB 0x00000001 /* RX MAC Enable */
448 #define MAC_RXCFG_SPAD 0x00000002 /* Strip Pad */
449 #define MAC_RXCFG_SFCS 0x00000004 /* Strip FCS */
450 #define MAC_RXCFG_PROM 0x00000008 /* Promiscuous Mode */
451 #define MAC_RXCFG_PGRP 0x00000010 /* Promiscuous Group */
452 #define MAC_RXCFG_HFE 0x00000020 /* Hash Filter Enable */
453 #define MAC_RXCFG_AFE 0x00000040 /* Address Filter Enable */
454 #define MAC_RXCFG_DDE 0x00000080 /* Disable Discard on Error */
455 #define MAC_RXCFG_RCE 0x00000100 /* RX Carrier Extension */
457 /* MAC Control Config Register. */
458 #define MAC_MCCFG_SPE 0x00000001 /* Send Pause Enable */
459 #define MAC_MCCFG_RPE 0x00000002 /* Receive Pause Enable */
460 #define MAC_MCCFG_PMC 0x00000004 /* Pass MAC Control */
461 
462 /* XIF Configuration Register.
463  *
464  * NOTE: When leaving or entering loopback mode, a global hardware
465  * init of GEM should be performed.
466  */
467 #define MAC_XIFCFG_OE 0x00000001 /* MII TX Output Driver Enable */
468 #define MAC_XIFCFG_LBCK 0x00000002 /* Loopback TX to RX */
469 #define MAC_XIFCFG_DISE 0x00000004 /* Disable RX path during TX */
470 #define MAC_XIFCFG_GMII 0x00000008 /* Use GMII clocks + datapath */
471 #define MAC_XIFCFG_MBOE 0x00000010 /* Controls MII_BUF_EN pin */
472 #define MAC_XIFCFG_LLED 0x00000020 /* Force LINKLED# active (low) */
473 #define MAC_XIFCFG_FLED 0x00000040 /* Force FDPLXLED# active (low) */
474 
475 /* InterPacketGap0 Register. This 8-bit value is used as an extension
476  * to the InterPacketGap1 Register. Specifically it contributes to the
477  * timing of the RX-to-TX IPG. This value is ignored and presumed to
478  * be zero for TX-to-TX IPG calculations and/or when the Enable IPG0 bit
479  * is cleared in the TX MAC Configuration Register.
480  *
481  * This value in this register in terms of media byte time.
482  *
483  * Recommended value: 0x00
484  */
485 
486 /* InterPacketGap1 Register. This 8-bit value defines the first 2/3
487  * portion of the Inter Packet Gap.
488  *
489  * This value in this register in terms of media byte time.
490  *
491  * Recommended value: 0x08
492  */
493 
494 /* InterPacketGap2 Register. This 8-bit value defines the second 1/3
495  * portion of the Inter Packet Gap.
496  *
497  * This value in this register in terms of media byte time.
498  *
499  * Recommended value: 0x04
500  */
501 
502 /* Slot Time Register. This 10-bit value specifies the slot time
503  * parameter in units of media byte time. It determines the physical
504  * span of the network.
505  *
506  * Recommended value: 0x40
507  */
508 
509 /* Minimum Frame Size Register. This 10-bit register specifies the
510  * smallest sized frame the TXMAC will send onto the medium, and the
511  * RXMAC will receive from the medium.
512  *
513  * Recommended value: 0x40
514  */
515 
516 /* Maximum Frame and Burst Size Register.
517  *
518  * This register specifies two things. First it specifies the maximum
519  * sized frame the TXMAC will send and the RXMAC will recognize as
520  * valid. Second, it specifies the maximum run length of a burst of
521  * packets sent in half-duplex gigabit modes.
522  *
523  * Recommended value: 0x200005ee
524  */
525 #define MAC_MAXFSZ_MFS 0x00007fff /* Max Frame Size */
526 #define MAC_MAXFSZ_MBS 0x7fff0000 /* Max Burst Size */
527 
528 /* PA Size Register. This 10-bit register specifies the number of preamble
529  * bytes which will be transmitted at the beginning of each frame. A
530  * value of two or greater should be programmed here.
531  *
532  * Recommended value: 0x07
533  */
534 
535 /* Jam Size Register. This 4-bit register specifies the duration of
536  * the jam in units of media byte time.
537  *
538  * Recommended value: 0x04
539  */
540 
541 /* Attempts Limit Register. This 8-bit register specifies the number
542  * of attempts that the TXMAC will make to transmit a frame, before it
543  * resets its Attempts Counter. After reaching the Attempts Limit the
544  * TXMAC may or may not drop the frame, as determined by the NGU
545  * (Never Give Up) and NGUL (Never Give Up Limit) bits in the TXMAC
546  * Configuration Register.
547  *
548  * Recommended value: 0x10
549  */
550 
551 /* MAX Control Type Register. This 16-bit register specifies the
552  * "type" field of a MAC Control frame. The TXMAC uses this field to
553  * encapsulate the MAC Control frame for transmission, and the RXMAC
554  * uses it for decoding valid MAC Control frames received from the
555  * network.
556  *
557  * Recommended value: 0x8808
558  */
559 
560 /* MAC Address Registers. Each of these registers specify the
561  * ethernet MAC of the interface, 16-bits at a time. Register
562  * 0 specifies bits [47:32], register 1 bits [31:16], and register
563  * 2 bits [15:0].
564  *
565  * Registers 3 through and including 5 specify an alternate
566  * MAC address for the interface.
567  *
568  * Registers 6 through and including 8 specify the MAC Control
569  * Address, which must be the reserved multicast address for MAC
570  * Control frames.
571  *
572  * Example: To program primary station address a:b:c:d:e:f into
573  * the chip.
574  * MAC_Address_2 = (a << 8) | b
575  * MAC_Address_1 = (c << 8) | d
576  * MAC_Address_0 = (e << 8) | f
577  */
578 
579 /* Address Filter Registers. Registers 0 through 2 specify bit
580  * fields [47:32] through [15:0], respectively, of the address
581  * filter. The Address Filter 2&1 Mask Register denotes the 8-bit
582  * nibble mask for Address Filter Registers 2 and 1. The Address
583  * Filter 0 Mask Register denotes the 16-bit mask for the Address
584  * Filter Register 0.
585  */
586 
587 /* Hash Table Registers. Registers 0 through 15 specify bit fields
588  * [255:240] through [15:0], respectively, of the hash table.
589  */
590 
591 /* Statistics Registers. All of these registers are 16-bits and
592  * track occurrences of a specific event. GEM can be configured
593  * to interrupt the host cpu when any of these counters overflow.
594  * They should all be explicitly initialized to zero when the interface
595  * is brought up.
596  */
598 /* Random Number Seed Register. This 10-bit value is used as the
599  * RNG seed inside GEM for the CSMA/CD backoff algorithm. It is
600  * recommended to program this register to the 10 LSB of the
601  * interfaces MAC address.
602  */
604 /* Pause Timer, read-only. This 16-bit timer is used to time the pause
605  * interval as indicated by a received pause flow control frame.
606  * A non-zero value in this timer indicates that the MAC is currently in
607  * the paused state.
608  */
609 
610 /* MIF Registers */
611 #define MIF_BBCLK 0x6200UL /* MIF Bit-Bang Clock */
612 #define MIF_BBDATA 0x6204UL /* MIF Bit-Band Data */
613 #define MIF_BBOENAB 0x6208UL /* MIF Bit-Bang Output Enable */
614 #define MIF_FRAME 0x620CUL /* MIF Frame/Output Register */
615 #define MIF_CFG 0x6210UL /* MIF Configuration Register */
616 #define MIF_MASK 0x6214UL /* MIF Mask Register */
617 #define MIF_STATUS 0x6218UL /* MIF Status Register */
618 #define MIF_SMACHINE 0x621CUL /* MIF State Machine Register */
619 
620 /* MIF Bit-Bang Clock. This 1-bit register is used to generate the
621  * MDC clock waveform on the MII Management Interface when the MIF is
622  * programmed in the "Bit-Bang" mode. Writing a '1' after a '0' into
623  * this register will create a rising edge on the MDC, while writing
624  * a '0' after a '1' will create a falling edge. For every bit that
625  * is transferred on the management interface, both edges have to be
626  * generated.
627  */
628 
629 /* MIF Bit-Bang Data. This 1-bit register is used to generate the
630  * outgoing data (MDO) on the MII Management Interface when the MIF
631  * is programmed in the "Bit-Bang" mode. The daa will be steered to the
632  * appropriate MDIO based on the state of the PHY_Select bit in the MIF
633  * Configuration Register.
634  */
636 /* MIF Big-Band Output Enable. THis 1-bit register is used to enable
637  * ('1') or disable ('0') the I-directional driver on the MII when the
638  * MIF is programmed in the "Bit-Bang" mode. The MDIO should be enabled
639  * when data bits are transferred from the MIF to the transceiver, and it
640  * should be disabled when the interface is idle or when data bits are
641  * transferred from the transceiver to the MIF (data portion of a read
642  * instruction). Only one MDIO will be enabled at a given time, depending
643  * on the state of the PHY_Select bit in the MIF Configuration Register.
644  */
645 
646 /* MIF Configuration Register. This 15-bit register controls the operation
647  * of the MIF.
648  */
649 #define MIF_CFG_PSELECT 0x00000001 /* Xcvr slct: 0=mdio0 1=mdio1 */
650 #define MIF_CFG_POLL 0x00000002 /* Enable polling mechanism */
651 #define MIF_CFG_BBMODE 0x00000004 /* 1=bit-bang 0=frame mode */
652 #define MIF_CFG_PRADDR 0x000000f8 /* Xcvr poll register address */
653 #define MIF_CFG_MDI0 0x00000100 /* MDIO_0 present or read-bit */
654 #define MIF_CFG_MDI1 0x00000200 /* MDIO_1 present or read-bit */
655 #define MIF_CFG_PPADDR 0x00007c00 /* Xcvr poll PHY address */
657 /* MIF Frame/Output Register. This 32-bit register allows the host to
658  * communicate with a transceiver in frame mode (as opposed to big-bang
659  * mode). Writes by the host specify an instrution. After being issued
660  * the host must poll this register for completion. Also, after
661  * completion this register holds the data returned by the transceiver
662  * if applicable.
663  */
664 #define MIF_FRAME_ST 0xc0000000 /* STart of frame */
665 #define MIF_FRAME_OP 0x30000000 /* OPcode */
666 #define MIF_FRAME_PHYAD 0x0f800000 /* PHY ADdress */
667 #define MIF_FRAME_REGAD 0x007c0000 /* REGister ADdress */
668 #define MIF_FRAME_TAMSB 0x00020000 /* Turn Around MSB */
669 #define MIF_FRAME_TALSB 0x00010000 /* Turn Around LSB */
670 #define MIF_FRAME_DATA 0x0000ffff /* Instruction Payload */
672 /* MIF Status Register. This register reports status when the MIF is
673  * operating in the poll mode. The poll status field is auto-clearing
674  * on read.
675  */
676 #define MIF_STATUS_DATA 0xffff0000 /* Live image of XCVR reg */
677 #define MIF_STATUS_STAT 0x0000ffff /* Which bits have changed */
679 /* MIF Mask Register. This 16-bit register is used when in poll mode
680  * to say which bits of the polled register will cause an interrupt
681  * when changed.
682  */
683 
684 /* PCS/Serialink Registers */
685 #define PCS_MIICTRL 0x9000UL /* PCS MII Control Register */
686 #define PCS_MIISTAT 0x9004UL /* PCS MII Status Register */
687 #define PCS_MIIADV 0x9008UL /* PCS MII Advertisement Reg */
688 #define PCS_MIILP 0x900CUL /* PCS MII Link Partner Ability */
689 #define PCS_CFG 0x9010UL /* PCS Configuration Register */
690 #define PCS_SMACHINE 0x9014UL /* PCS State Machine Register */
691 #define PCS_ISTAT 0x9018UL /* PCS Interrupt Status Reg */
692 #define PCS_DMODE 0x9050UL /* Datapath Mode Register */
693 #define PCS_SCTRL 0x9054UL /* Serialink Control Register */
694 #define PCS_SOS 0x9058UL /* Shared Output Select Reg */
695 #define PCS_SSTATE 0x905CUL /* Serialink State Register */
697 /* PCD MII Control Register. */
698 #define PCS_MIICTRL_SPD 0x00000040 /* Read as one, writes ignored */
699 #define PCS_MIICTRL_CT 0x00000080 /* Force COL signal active */
700 #define PCS_MIICTRL_DM 0x00000100 /* Duplex mode, forced low */
701 #define PCS_MIICTRL_RAN 0x00000200 /* Restart auto-neg, self clear */
702 #define PCS_MIICTRL_ISO 0x00000400 /* Read as zero, writes ignored */
703 #define PCS_MIICTRL_PD 0x00000800 /* Read as zero, writes ignored */
704 #define PCS_MIICTRL_ANE 0x00001000 /* Auto-neg enable */
705 #define PCS_MIICTRL_SS 0x00002000 /* Read as zero, writes ignored */
706 #define PCS_MIICTRL_WB 0x00004000 /* Wrapback, loopback at 10-bit
707  * input side of Serialink
708  */
709 #define PCS_MIICTRL_RST 0x00008000 /* Resets PCS, self clearing */
711 /* PCS MII Status Register. */
712 #define PCS_MIISTAT_EC 0x00000001 /* Ext Capability: Read as zero */
713 #define PCS_MIISTAT_JD 0x00000002 /* Jabber Detect: Read as zero */
714 #define PCS_MIISTAT_LS 0x00000004 /* Link Status: 1=up 0=down */
715 #define PCS_MIISTAT_ANA 0x00000008 /* Auto-neg Ability, always 1 */
716 #define PCS_MIISTAT_RF 0x00000010 /* Remote Fault */
717 #define PCS_MIISTAT_ANC 0x00000020 /* Auto-neg complete */
718 #define PCS_MIISTAT_ES 0x00000100 /* Extended Status, always 1 */
720 /* PCS MII Advertisement Register. */
721 #define PCS_MIIADV_FD 0x00000020 /* Advertise Full Duplex */
722 #define PCS_MIIADV_HD 0x00000040 /* Advertise Half Duplex */
723 #define PCS_MIIADV_SP 0x00000080 /* Advertise Symmetric Pause */
724 #define PCS_MIIADV_AP 0x00000100 /* Advertise Asymmetric Pause */
725 #define PCS_MIIADV_RF 0x00003000 /* Remote Fault */
726 #define PCS_MIIADV_ACK 0x00004000 /* Read-only */
727 #define PCS_MIIADV_NP 0x00008000 /* Next-page, forced low */
729 /* PCS MII Link Partner Ability Register. This register is equivalent
730  * to the Link Partnet Ability Register of the standard MII register set.
731  * It's layout corresponds to the PCS MII Advertisement Register.
732  */
734 /* PCS Configuration Register. */
735 #define PCS_CFG_ENABLE 0x00000001 /* Must be zero while changing
736  * PCS MII advertisement reg.
737  */
738 #define PCS_CFG_SDO 0x00000002 /* Signal detect override */
739 #define PCS_CFG_SDL 0x00000004 /* Signal detect active low */
740 #define PCS_CFG_JS 0x00000018 /* Jitter-study:
741  * 0 = normal operation
742  * 1 = high-frequency test pattern
743  * 2 = low-frequency test pattern
744  * 3 = reserved
745  */
746 #define PCS_CFG_TO 0x00000020 /* 10ms auto-neg timer override */
748 /* PCS Interrupt Status Register. This register is self-clearing
749  * when read.
750  */
751 #define PCS_ISTAT_LSC 0x00000004 /* Link Status Change */
752 
753 /* Datapath Mode Register. */
754 #define PCS_DMODE_SM 0x00000001 /* 1 = use internal Serialink */
755 #define PCS_DMODE_ESM 0x00000002 /* External SERDES mode */
756 #define PCS_DMODE_MGM 0x00000004 /* MII/GMII mode */
757 #define PCS_DMODE_GMOE 0x00000008 /* GMII Output Enable */
759 /* Serialink Control Register.
760  *
761  * NOTE: When in SERDES mode, the loopback bit has inverse logic.
762  */
763 #define PCS_SCTRL_LOOP 0x00000001 /* Loopback enable */
764 #define PCS_SCTRL_ESCD 0x00000002 /* Enable sync char detection */
765 #define PCS_SCTRL_LOCK 0x00000004 /* Lock to reference clock */
766 #define PCS_SCTRL_EMP 0x00000018 /* Output driver emphasis */
767 #define PCS_SCTRL_STEST 0x000001c0 /* Self test patterns */
768 #define PCS_SCTRL_PDWN 0x00000200 /* Software power-down */
769 #define PCS_SCTRL_RXZ 0x00000c00 /* PLL input to Serialink */
770 #define PCS_SCTRL_RXP 0x00003000 /* PLL input to Serialink */
771 #define PCS_SCTRL_TXZ 0x0000c000 /* PLL input to Serialink */
772 #define PCS_SCTRL_TXP 0x00030000 /* PLL input to Serialink */
774 /* Shared Output Select Register. For test and debug, allows multiplexing
775  * test outputs into the PROM address pins. Set to zero for normal
776  * operation.
777  */
778 #define PCS_SOS_PADDR 0x00000003 /* PROM Address */
780 /* PROM Image Space */
781 #define PROM_START 0x100000UL /* Expansion ROM run time access*/
782 #define PROM_SIZE 0x0fffffUL /* Size of ROM */
783 #define PROM_END 0x200000UL /* End of ROM */
785 /* MII definitions missing from mii.h */
786 
787 #define BMCR_SPD2 0x0040 /* Gigabit enable? (bcm5411) */
788 #define LPA_PAUSE 0x0400
789 
790 /* More PHY registers (specific to Broadcom models) */
792 /* MII BCM5201 MULTIPHY interrupt register */
793 #define MII_BCM5201_INTERRUPT 0x1A
794 #define MII_BCM5201_INTERRUPT_INTENABLE 0x4000
795 
796 #define MII_BCM5201_AUXMODE2 0x1B
797 #define MII_BCM5201_AUXMODE2_LOWPOWER 0x0008
798 
799 #define MII_BCM5201_MULTIPHY 0x1E
800 
801 /* MII BCM5201 MULTIPHY register bits */
802 #define MII_BCM5201_MULTIPHY_SERIALMODE 0x0002
803 #define MII_BCM5201_MULTIPHY_SUPERISOLATE 0x0008
804 
805 /* MII BCM5400 1000-BASET Control register */
806 #define MII_BCM5400_GB_CONTROL 0x09
807 #define MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP 0x0200
809 /* MII BCM5400 AUXCONTROL register */
810 #define MII_BCM5400_AUXCONTROL 0x18
811 #define MII_BCM5400_AUXCONTROL_PWR10BASET 0x0004
813 /* MII BCM5400 AUXSTATUS register */
814 #define MII_BCM5400_AUXSTATUS 0x19
815 #define MII_BCM5400_AUXSTATUS_LINKMODE_MASK 0x0700
816 #define MII_BCM5400_AUXSTATUS_LINKMODE_SHIFT 8
818 /* When it can, GEM internally caches 4 aligned TX descriptors
819  * at a time, so that it can use full cacheline DMA reads.
820  *
821  * Note that unlike HME, there is no ownership bit in the descriptor
822  * control word. The same functionality is obtained via the TX-Kick
823  * and TX-Complete registers. As a result, GEM need not write back
824  * updated values to the TX descriptor ring, it only performs reads.
825  *
826  * Since TX descriptors are never modified by GEM, the driver can
827  * use the buffer DMA address as a place to keep track of allocated
828  * DMA mappings for a transmitted packet.
829  */
830 struct gem_txd {
832  __le64 buffer;
833 };
834 
835 #define TXDCTRL_BUFSZ 0x0000000000007fffULL /* Buffer Size */
836 #define TXDCTRL_CSTART 0x00000000001f8000ULL /* CSUM Start Offset */
837 #define TXDCTRL_COFF 0x000000001fe00000ULL /* CSUM Stuff Offset */
838 #define TXDCTRL_CENAB 0x0000000020000000ULL /* CSUM Enable */
839 #define TXDCTRL_EOF 0x0000000040000000ULL /* End of Frame */
840 #define TXDCTRL_SOF 0x0000000080000000ULL /* Start of Frame */
841 #define TXDCTRL_INTME 0x0000000100000000ULL /* "Interrupt Me" */
842 #define TXDCTRL_NOCRC 0x0000000200000000ULL /* No CRC Present */
844 /* GEM requires that RX descriptors are provided four at a time,
845  * aligned. Also, the RX ring may not wrap around. This means that
846  * there will be at least 4 unused descriptor entries in the middle
847  * of the RX ring at all times.
848  *
849  * Similar to HME, GEM assumes that it can write garbage bytes before
850  * the beginning of the buffer and right after the end in order to DMA
851  * whole cachelines.
852  *
853  * Unlike for TX, GEM does update the status word in the RX descriptors
854  * when packets arrive. Therefore an ownership bit does exist in the
855  * RX descriptors. It is advisory, GEM clears it but does not check
856  * it in any way. So when buffers are posted to the RX ring (via the
857  * RX Kick register) by the driver it must make sure the buffers are
858  * truly ready and that the ownership bits are set properly.
859  *
860  * Even though GEM modifies the RX descriptors, it guarantees that the
861  * buffer DMA address field will stay the same when it performs these
862  * updates. Therefore it can be used to keep track of DMA mappings
863  * by the host driver just as in the TX descriptor case above.
864  */
865 struct gem_rxd {
868 };
869 
870 #define RXDCTRL_TCPCSUM 0x000000000000ffffULL /* TCP Pseudo-CSUM */
871 #define RXDCTRL_BUFSZ 0x000000007fff0000ULL /* Buffer Size */
872 #define RXDCTRL_OWN 0x0000000080000000ULL /* GEM owns this entry */
873 #define RXDCTRL_HASHVAL 0x0ffff00000000000ULL /* Hash Value */
874 #define RXDCTRL_HPASS 0x1000000000000000ULL /* Passed Hash Filter */
875 #define RXDCTRL_ALTMAC 0x2000000000000000ULL /* Matched ALT MAC */
876 #define RXDCTRL_BAD 0x4000000000000000ULL /* Frame has bad CRC */
877 
878 #define RXDCTRL_FRESH(gp) \
879  ((((RX_BUF_ALLOC_SIZE(gp) - RX_OFFSET) << 16) & RXDCTRL_BUFSZ) | \
880  RXDCTRL_OWN)
881 
882 #define TX_RING_SIZE 128
883 #define RX_RING_SIZE 128
884 
885 #if TX_RING_SIZE == 32
886 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_32
887 #elif TX_RING_SIZE == 64
888 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_64
889 #elif TX_RING_SIZE == 128
890 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_128
891 #elif TX_RING_SIZE == 256
892 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_256
893 #elif TX_RING_SIZE == 512
894 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_512
895 #elif TX_RING_SIZE == 1024
896 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_1K
897 #elif TX_RING_SIZE == 2048
898 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_2K
899 #elif TX_RING_SIZE == 4096
900 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_4K
901 #elif TX_RING_SIZE == 8192
902 #define TXDMA_CFG_BASE TXDMA_CFG_RINGSZ_8K
903 #else
904 #error TX_RING_SIZE value is illegal...
905 #endif
907 #if RX_RING_SIZE == 32
908 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_32
909 #elif RX_RING_SIZE == 64
910 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_64
911 #elif RX_RING_SIZE == 128
912 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_128
913 #elif RX_RING_SIZE == 256
914 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_256
915 #elif RX_RING_SIZE == 512
916 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_512
917 #elif RX_RING_SIZE == 1024
918 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_1K
919 #elif RX_RING_SIZE == 2048
920 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_2K
921 #elif RX_RING_SIZE == 4096
922 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_4K
923 #elif RX_RING_SIZE == 8192
924 #define RXDMA_CFG_BASE RXDMA_CFG_RINGSZ_8K
925 #else
926 #error RX_RING_SIZE is illegal...
927 #endif
929 #define NEXT_TX(N) (((N) + 1) & (TX_RING_SIZE - 1))
930 #define NEXT_RX(N) (((N) + 1) & (RX_RING_SIZE - 1))
932 #define TX_BUFFS_AVAIL(GP) \
933  (((GP)->tx_old <= (GP)->tx_new) ? \
934  (GP)->tx_old + (TX_RING_SIZE - 1) - (GP)->tx_new : \
935  (GP)->tx_old - (GP)->tx_new - 1)
937 #define RX_OFFSET 2
938 #define RX_BUF_ALLOC_SIZE(gp) ((gp)->rx_buf_sz + 28 + RX_OFFSET + 64)
940 #define RX_COPY_THRESHOLD 256
941 
942 #if TX_RING_SIZE < 128
943 #define INIT_BLOCK_TX_RING_SIZE 128
944 #else
945 #define INIT_BLOCK_TX_RING_SIZE TX_RING_SIZE
946 #endif
948 #if RX_RING_SIZE < 128
949 #define INIT_BLOCK_RX_RING_SIZE 128
950 #else
951 #define INIT_BLOCK_RX_RING_SIZE RX_RING_SIZE
952 #endif
957 };
959 enum gem_phy_type {
963  phy_serdes,
964 };
965 
967  link_down = 0, /* No link, will retry */
968  link_aneg, /* Autoneg in progress */
969  link_force_try, /* Try Forced link speed */
970  link_force_ret, /* Forced mode worked, retrying autoneg */
971  link_force_ok, /* Stay in forced mode */
972  link_up /* Link is up */
973 };
975 struct gem {
976  void __iomem *regs;
980  unsigned int has_wol : 1; /* chip supports wake-on-lan */
981  unsigned int asleep_wol : 1; /* was asleep with WOL enabled */
984  u32 msg_enable;
988 
993  int rx_buf_sz;
996  u32 mac_rx_cfg;
997  u32 swrst_base;
998 
999  int want_autoneg;
1000  int last_forced_speed;
1002  struct timer_list link_timer;
1003  int timer_ticks;
1004  int wake_on_lan;
1005  struct work_struct reset_task;
1006  volatile int reset_task_pending;
1007 
1008  enum gem_phy_type phy_type;
1009  struct mii_phy phy_mii;
1010  int mii_phy_addr;
1011 
1012  struct gem_init_block *init_block;
1013  struct sk_buff *rx_skbs[RX_RING_SIZE];
1014  struct sk_buff *tx_skbs[TX_RING_SIZE];
1016 
1017  struct pci_dev *pdev;
1018  struct net_device *dev;
1019 #if defined(CONFIG_PPC_PMAC) || defined(CONFIG_SPARC)
1020  struct device_node *of_node;
1021 #endif
1022 };
1023 
1024 #define found_mii_phy(gp) ((gp->phy_type == phy_mii_mdio0 || gp->phy_type == phy_mii_mdio1) && \
1025  gp->phy_mii.def && gp->phy_mii.def->ops)
1026 
1027 #endif /* _SUNGEM_H */