wg302v2-setup.c

Go to the documentation of this file.

/*
 * arch/arm/mach-ixp4xx/wg302-setup.c
 *
 * Board setup for the Netgear WG302 v2 and WAG302 v2
 *
 * Copyright (C) 2007 Imre Kaloz <[email protected]>
 *
 * based on coyote-setup.c:
 *      Copyright (C) 2003-2005 MontaVista Software, Inc.
 *
 * Author: Imre Kaloz <[email protected]>
 *
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/serial_8250.h>

#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>

static struct flash_platform_data wg302v2_flash_data = {
    .map_name   = "cfi_probe",
    .width      = 2,
};

static struct resource wg302v2_flash_resource = {
    .flags      = IORESOURCE_MEM,
};

static struct platform_device wg302v2_flash = {
    .name       = "IXP4XX-Flash",
    .id     = 0,
    .dev        = {
        .platform_data = &wg302v2_flash_data,
    },
    .num_resources  = 1,
    .resource   = &wg302v2_flash_resource,
};

static struct resource wg302v2_uart_resource = {
    .start  = IXP4XX_UART2_BASE_PHYS,
    .end    = IXP4XX_UART2_BASE_PHYS + 0x0fff,
    .flags  = IORESOURCE_MEM,
};

static struct plat_serial8250_port wg302v2_uart_data[] = {
    {
        .mapbase    = IXP4XX_UART2_BASE_PHYS,
        .membase    = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
        .irq        = IRQ_IXP4XX_UART2,
        .flags      = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
        .iotype     = UPIO_MEM,
        .regshift   = 2,
        .uartclk    = IXP4XX_UART_XTAL,
    },
    { },
};

static struct platform_device wg302v2_uart = {
    .name       = "serial8250",
    .id     = PLAT8250_DEV_PLATFORM,
    .dev            = {
        .platform_data  = wg302v2_uart_data,
    },
    .num_resources  = 1,
    .resource   = &wg302v2_uart_resource,
};

static struct platform_device *wg302v2_devices[] __initdata = {
    &wg302v2_flash,
    &wg302v2_uart,
};

static void __init wg302v2_init(void)
{
    ixp4xx_sys_init();

    wg302v2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
    wg302v2_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;

    *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
    *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;

    platform_add_devices(wg302v2_devices, ARRAY_SIZE(wg302v2_devices));
}

#ifdef CONFIG_MACH_WG302V2
MACHINE_START(WG302V2, "Netgear WG302 v2 / WAG302 v2")
    /* Maintainer: Imre Kaloz <[email protected]> */
    .map_io     = ixp4xx_map_io,
    .init_early = ixp4xx_init_early,
    .init_irq   = ixp4xx_init_irq,
    .timer      = &ixp4xx_timer,
    .atag_offset    = 0x100,
    .init_machine   = wg302v2_init,
#if defined(CONFIG_PCI)
    .dma_zone_size  = SZ_64M,
#endif
    .restart    = ixp4xx_restart,
MACHINE_END
#endif