Using a Load Balancer - Getting Traffic into a Cluster over Non-Standard Ports | Developer Guide

Overview

If you do not need a specific external IP address, you can configure a load balancer service to allow external access to an OpenShift Origin cluster.

A load balancer service allocates a unique IP from a configured pool. The load balancer a single edge router IP (which can be a virtual IP (VIP), but is still a single machine for initial load balancing).

This process involves the following:

The administrator performs the prerequisites;
The developer creates a project and service, if the service to be exposed does not exist;
The developer exposes the service to create a route.
The developer creates the Load Balancer Service.
The network administrator configures networking to the service.

Administrator Prerequisites

Before starting this procedure, the administrator must:

Set up the external port to the cluster networking environment so that requests can reach the cluster. For example, names can be configured into DNS to point to specific nodes or other IP addresses in the cluster. The DNS wildcard feature can be used to configure a subset of names to an IP address in the cluster. This allows the users to set up routes within the cluster without further administrator attention.
Make sure that the local firewall on each node permits the request to reach the IP address.
Configure the OpenShift Origin cluster to use an Identity Provider that allows appropriate user access.
Make sure there is at least one user with cluster admin role. To add this role to a user, run the following command:
```
oadm policy add-cluster-role-to-user cluster-admin username
```
Have an OpenShift Origin cluster with at least one master and at least one node and a system outside the cluster that has network access to the cluster. This procedure assumes that the external system is on the same subnet as the cluster. The additional networking required for external systems on a different subnet is out-of-scope for this topic.

Defining the Public IP Range

The first step in allowing access to a service is to define an external IP address range in the master configuration file:

Log into OpenShift Origin as a user with the cluster admin role.

$ oc login
Authentication required (openshift)
Username: admin
Password:
Login successful.

You have access to the following projects and can switch between them with 'oc project <projectname>':
  * default
Using project "default".

Configure the externalIPNetworkCIDRs parameter in the /etc/origin/master/master-config.yaml file as shown:

networkConfig:
  externalIPNetworkCIDRs:
  - <ip_address>/<cidr>

For example:

networkConfig:
  externalIPNetworkCIDRs:
  - 192.168.120.0/24

Restart the OpenShift Origin master service to apply the changes.
```
# systemctl restart origin-master-api origin-master-controllers
```

The IP address pool must terminate at one or more nodes in the cluster.

Create a Project and Service

If the project and service that you want to expose do not exist, first create the project, then the service.

If the project and service already exist, go to the next step: Expose the Service to Create a Route.

Log into OpenShift Origin.

Create a new project for your service:

$ oc new-project <project_name>

For example:

$ oc new-project external-ip

Use the oc new-app command to create a service:

For example:

$ oc new-app \
    -e MYSQL_USER=admin \
    -e MYSQL_PASSWORD=redhat \
    -e MYSQL_DATABASE=mysqldb \
    registry.access.redhat.com/openshift3/mysql-55-rhel7

Run the following command to see that the new service is created:

oc get svc
NAME               CLUSTER-IP      EXTERNAL-IP   PORT(S)    AGE
mysql-55-rhel7     172.30.131.89   <none>        3306/TCP   13m

By default, the new service does not have an external IP address.

Expose the Service to Create a Route

You must expose the service as a route using the oc expose command.

To expose the service:

Log into OpenShift Origin.
Log into the project where the service you want to expose is located.
```
$ oc project project1
```

Run the following command to expose the route:

oc expose service <service-name>

For example:

oc expose service mysql-55-rhel7
route "mysql-55-rhel7" exposed

On the master, use a tool, such as cURL, to make sure you can reach the service using the cluster IP address for the service:
```
curl <pod-ip>:<port>
```
For example:
```
curl 172.30.131.89:3306
```
The examples in this section use a MySQL service, which requires a client application. If you get a string of characters with the Got packets out of order message, you are connected to the service.

If you have a MySQL client, log in with the standard CLI command:
```
$ mysql -h 172.30.131.89 -u admin -p
Enter password:
Welcome to the MariaDB monitor.  Commands end with ; or \g.

MySQL [(none)]>
```

Then, perform the following tasks:

Create the Load Balancer Service

To create a load balancer service:

Log into OpenShift Origin.
Load the project where the service you want to expose is located. If the project or service does not exist, see Create a Project and Service.
```
$ oc project project1
```

Open a text file on the master node and paste the following text, editing the file as needed:

Example 1. Sample load balancer configuration file

apiVersion: v1
kind: Service
metadata:
  name: egress-2 (1)
spec:
  ports:
  - name: db
    port: 3306 (2)
  loadBalancerIP:
  type: LoadBalancer (3)
  selector:
    name: mysql (4)

1	Enter a descriptive name for the load balancer service.
2	Enter the same port that the service you want to expose is listening on.
3	Enter `loadbalancer` as the type.
4	Enter the name of the service.

Save and exit the file.
Run the following command to create the service:
```
oc create -f <file-name>
```
For example:
```
oc create -f mysql-lb.yaml
```

Execute the following command to view the new service:

oc get svc
NAME              CLUSTER-IP       EXTERNAL-IP                   PORT(S)                   AGE
egress-2          172.30.236.167   172.29.121.74,172.29.121.74   3306/TCP                  6s

Note that the service has an external IP address automatically assigned.

On the master, use a tool, such as cURL, to make sure you can reach the service using the public IP address:
```
$ curl <public-ip>:<port>
```
++ For example:
```
$ curl 172.29.121.74:3306
```
The examples in this section use a MySQL service, which requires a client application. If you get a string of characters with the Got packets out of order message, you are connecting with the service:

If you have a MySQL client, log in with the standard CLI command:
```
$ mysql -h 172.30.131.89 -u admin -p
Enter password:
Welcome to the MariaDB monitor.  Commands end with ; or \g.

MySQL [(none)]>
```

Configuring Networking

The following steps are general guidelines for configuring the networking required to access the exposed service from other nodes. As network environments vary, consult your network administrator for specific configurations that need to be made within your environment.

These steps assume that all of the systems are on the same subnet.

On the Node:

Restart the network to make sure the network is up.
```
$ service network restart
Restarting network (via systemctl):  [  OK  ]
```
If the network is not up, you will receive error messages such as Network is unreachable when executing the following commands.
Add a route between the IP address of the exposed service on the master and the IP address of the master host:
```
$ route add -net 172.29.121.74 netmask 255.255.0.0 gw 10.16.41.22 dev eth0
```
Use a tool, such as cURL, to make sure you can reach the service using the public IP address:
```
$ curl <public-ip>:<port>
```
For example:
```
curl 172.29.121.74:3306
```
If you get a string of characters with the Got packets out of order message, your service is accessible from the node.

On the system that is not in the cluster:

Restart the network to make sure the network is up.
```
$ service network restart
Restarting network (via systemctl):  [  OK  ]
```
If the network is not up, you will receive error messages such as Network is unreachable when executing the following commands.
Add a route between the IP address of the exposed service on master and the IP address of the master host:
```
$ route add -net 172.29.121.74 netmask 255.255.0.0 gw 10.16.41.22 dev eth0
```
Make sure you can reach the service using the public IP address:
```
$ curl <public-ip>:<port>
```
For example:
```
curl 172.29.121.74:3306
```
If you get a string of characters with the Got packets out of order message, your service is accessible outside the cluster.

Configure IP Failover

Optionally, an administrator can configure IP failover.

IP failover manages a pool of Virtual IP (VIP) addresses on a set of nodes. Every VIP in the set is serviced by a node selected from the set. As long as a single node is available, the VIPs will be served. There is no way to explicitly distribute the VIPs over the nodes. As such, there may be nodes with no VIPs and other nodes with multiple VIPs. If there is only one node, all VIPs will be on it.

The VIPs must be routable from outside the cluster.

To configure IP failover:

On the master, make sure the ipfailover service account has sufficient security privileges:
```
oadm policy add-scc-to-user privileged -z ipfailover
```

Run the following command to create the IP failover:

oadm ipfailover --virtual-ips=<exposed-ip-address> --watch-port=<exposed-port> --replicas=<number-of-pods> --create

For example:

oadm ipfailover --virtual-ips="172.30.233.169" --watch-port=32315 --replicas=4 --create
--> Creating IP failover ipfailover ...
    serviceaccount "ipfailover" created
    deploymentconfig "ipfailover" created
--> Success

Using a Load Balancer to Get Traffic into the Cluster

Overview

Administrator Prerequisites

Defining the Public IP Range

Create a Project and Service

Expose the Service to Create a Route

Create the Load Balancer Service

Configuring Networking

Configure IP Failover